Covered Task - Kinder Morgan

More documents

Recommendations

Info

2. Be able to visually identify leakage3. Be aware of OQ qualification requirements for inspection of atmospheric coatings (Covered Task 102.09)E. Know procedures to notify Operations prior to operation of valveF. Be able to safely operate the valve to verify that it operates properlyG. Return valve to original position1. Be able to verify original position, using valve stem or valve position indicator rod if availableH. Re-lock in proper position or provide security as appropriate1. Be able to secure locking device, usually chain and lock2. Be able to verify valve is in original positionI. Know proper documentation proceduresJ. Be able to recognize and respond to abnormal operating conditions that might be encountered when performing this covered task.104.08 Moving in-service pipeA. Be able to determine the product type (MSDS, DOT Part 195)1. Know who to contact to determine the product which will be at the job site during the work.2. If product is a Highly Volatile Liquid (HVL), be aware of pressure restrictions and isolation requirements prior to moving the pipe (DOT Part 195.424).B. Profile pipeline.1. Be aware of OQ qualification requirements for locating pipeline (Covered Task 104.22)2. Be able to determine existing location of pipeline3. Be able to approximately determine local soil conditions (sand, clay, rock, drainage)4. Be able to identify approximate new location of pipelineC. Review pipeline drawings1. Be able to read and understand information on pipeline drawings, such as wall thickness, grade of steel, diameter of pipe, pipe bends, pipe fittings.2. Know procedure for notification to KMEP Environmental Dept. for their review prior to commencement of excavation.3. Ensure that all welds within the area of relocation have been non-destructively tested, if applicable.D. Excavation1. Be aware of KMEP requirements for excavation near the pipeline.2. Be familiar with KMEP procedures for working safely in an excavation3. Be aware of all permit requirements, such as environmental, excavation, etc.4. Be aware of all environmental concerns, such as permitting, water disposition and erosion control.5. When excavating around the pipeline, be able to determine proper depth of excavation to ensure adequate working room around pipeline.6. When excavating around the pipeline, be able to provide adequate support (such as dirt or skids) to exposed pipeline.E. Pipe/coating inspection.1. Be aware of OQ qualification requirements for inspecting buried pipe when exposed (Covered Task 104.01).F. Moving the pipeline.1. Be aware of steps necessary to prepare new bed, such as crumbing or bedding the ditch2. Be aware of advantages and disadvantages of various mechanical lifting devices (side booms, boom trucks, etc.)3. Understand safe rigging and lifting procedures.4. Be aware of safety precautions associated with lowering the pipeline, such as skid removal, internal pressure restrictions, and local requirements for isolation ofthe pipeline being relocated.5. In areas where little or no slack is available on the pipeline, be aware of how to insure secondary stresses are minimized.Page 20 of 33
G. Backfilling1. Be aware of OQ qualification requirements for backfilling the pipeline trench (Covered Task 104.11).H. Pressure monitoring1. Be aware of company procedures for pressure testing a relocated pipeline.I. Be aware of company procedures for proper documentation procedures.J. Be able to recognize and respond to abnormal operating conditions that might be encountered when performing this covered task.104.09 Inspection of clearance of existing pipe to underground structuresA. Be aware of KM policy on proximity of foreign crossing for physical clearanceB. Be aware of company policies for working in an excavation and for safe work permittingC. Be aware of possible cathodic interferences between structure and pipeline and know procedure for advising Corrosion Department of proposed clearance.D. Be aware of OQ qualification requirements for inspection of buried pipe (Covered Task 104.01).E. Be aware of company procedures for proper documentationF. Be able to recognize and respond to abnormal operating conditions that might be encountered when performing this covered task.104.10 Inspection of support structures on existing aboveground componentsA. Be able to inspect support structures according to manufacturer’s instructions and the local proceduresB. Be able to recognize and respond to abnormal operating conditions that might be encountered when performing this covered task104.11 Backfilling an excavationA. Inspection of backfill for damaging materials1. Be able to verify ditch is free of any debris.2. Be able to verify backfill material is acceptably free of rocks and debris.B. Protect pipe coating1. Be able to ensure pipe coating will not be damaged with backfilling the hole or when compacting backfill around pipe.2. In rocky soil, ensure a rock shield coating or equivalent protection is used.3. Be able to ensure compaction work does not damage pipe or coating.C. Ensure correct cover over pipeline, being aware of cover requirements in DOT Part 195D. Be aware of OQ qualification requirements for inspection of buried pipe when exposed (Covered Task 104.01)E. Be able to recognize and respond to abnormal operating conditions that might be encountered when performing this covered task.104.12 General pipeline repair – ClockspringA. Be aware that all Company health and safety guidelines (safe work permit) must be met prior to commencement of workB. Be aware that installation of Clockspring device requires vendor training and certificationC. Be familiar with Company procedures for working safely in an excavationD. Be aware of OQ qualifications for coating removal and pipeline surface preparation prior to application of repair material and coating repair after installation ofClockspring (Covered Task 102.13).Page 21 of 33
Page 1 and 2: Appendix BKinder Morgan Operator Qu
Page 8 and 9: Detailed Covered Task Descriptions1
Page 10 and 11: Page 10 of 33
Page 12 and 13: C. Be able to recognize and respond
Page 14 and 15: B. Be able to recognize and respond
Page 16 and 17: E. Be able to recognize and respond
Page 18 and 19: 104.01 Inspect buried pipe when exp
Page 22 and 23: E. Be aware of manufacturer’s ins
Page 24 and 25: G. Be able to have all required equ
Page 26 and 27: 104.23 Temporary marking of Pipelin
Page 28 and 29: E. Be able to recognize and respond
Page 30 and 31: 1. Be able to isolate the launcher/
Page 32 and 33: B. Be able to identify type, manufa

Covered Task - Kinder Morgan

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?