plastic tabletop chains - FB Kjeder

More documents

Recommendations

Info

The sideflexing belts range exists of 1 ⁄2-inch pitch 505, 1 1 ⁄4-inch pitch 1200 and 1 1 ⁄4-inch pitch 7956 belts, offering asolution for almost any curved application. As a standard the belts are supplied in low friction acetal for beverageand in acetal or polypropylene with antibacterial protection, especially for direct food contact.FEATURESSIDEFLEXING MODULAR BELTS• In compliance with the industry standards, three curve guiding systems are offered:RBP uses beveled Positrack lugs underneath the belt to guide the belt in the curve. The lugs runagainst a beveled strip, retaining the belt in the curve.This system enables easy removal of the belt from the conveyor for cleaning or maintenance.The conveyed product can be wider than the belt width as there is no wearstrip on top of thebelt to hold it down.RBT guiding uses Tabs underneath the belt to hold the belt down while running through thecurve.Often the tabs can also be used to hang the belt in the return part of the conveyor. Dependingon the construction modular belts with tabs are more difficult to remove from the conveyor forcleaning and maintenance.RB (Flat belt without Tabs or Positrack) is suitable for the conventional guiding method,supporting the belt on its inner radius. The belt is held down in the curve by a wearstrip ontop of the belt or by running through a U-channel.This method can also be applied in the return part. In this way it is difficult to remove the beltfrom the conveyor. The RB executions are also suitable for low-tension spiral applications.• Belt and curve guiding materials have a PV (Pressure/Velocity)-limit determining the maximum speed or load ina specific application. Rexnords calculation software and engineering manuals will advise concerning the feasibilityof a specific application. For spiral applications it is recommended to discuss with a qualified OEM retrofit or designdetails, to avoid overload issues or failures.PROGRAMME505-Series1200-Series7956-SeriesBelt accessoriesFor small packed products and loose foodstuff; combines a small internal radius with minimum inline transfers andan open area of 10%; available in RBP and RBFor food, beverage, packaging and other industries. Combines a 39% open area and cleanable design with a surfaceoptimized for product support. There are several types:• 1255 standard execution; available in RBP and RB; RBT upon request• 1255 SuperGrip with rubber for inclined and declined applications; available in RBP and RB• 1265 combines standard 1255 inner modules with specially designed outer end modules with TAB and specialsliding blocks for huge loading, high-speed possibilities; available in RBT on the outer radius, the inner radius canbe equipped with RBP, RBT and RB• 1275 combines standard 1255 outer modules with specially designed inner modules, creating a compact radiusdesign from 1.2 collapse factor upwards; available in RBP, RBT and RB• 1285 combines the 1265 outer and 1275 inner modules for high strength, high speed and compact design.RBT guiding on the outer radius, the inner radius can be equipped with RBP, RBT and RBFor large and heavy products in beverage and case handling applications; the inside radius is 2 times the belt widthand the 16% open area offers maximum product support; the belt features the same strength rating for straight andcurved sections. There are several types:• 7956 NT without tabs• 7956 TAB with original hold down tabs• 7956 GT with high performance tabs with similar dimensions as the bearing option• 7956 B with bearings every second row for high-speed and huge load applicationsFlights on 1255 for inclined and declined applications in food industry196PACK CONVEYOR WITH 505 BELT 1275 BELT BOXES CONVEYED THROUGH CURVE WITH 1285 BELT
505-SERIESpage 198page 198page 208RADIUS505Assembly Belt type Code nr.* Width Sideflex Working load (max.) Temperature range Weight Backflexradius inside °C radiusA (min.) straight in curve (min.)mm mm N/m N dry wet kg/m 2 mmWITH SPECIAL REINFORCED PLASTIC PINSFLAT RB 505 XLG 255 867.20.12 255 510RB 505 XLG 340 867.20.13 340 680RB 505 XLG 425 867.20.14 425 850 15000RB 505 XLG 510 867.20.15 510 1020RB 505 XLG 595 867.20.16 595 1190RB 505 XLG 680 867.20.17 680 1360POSITRACK RBP 505 XLG 255 867.30.12 255 510TWO SIDES RBP 505 XLG 340 867.30.13 340 680RBP 505 XLG 425 867.30.14 425 850RBP 505 XLG 510 867.30.15 510 1020RBP 505 XLG 595 867.30.16 595 1190RBP 505 XLG 680 867.30.17 680 13601300 -40 to +80 -40 to +65 9.0 1515000 1300 -40 to +80 -40 to +65 9.0 15ANTIBACTERIAL WSA-ACETAL WITH PBT PINSFLAT WSA 505 RB 868.20.xxPOSITRACK WSA 505 RBP 868.30.xx255 to 680 2x belt width 15000 1300 -40 to +80 -40 to +65 9.0 15ANTIBACTERIAL BSA-ACETAL WITH PBT PINSFLAT BSA 505 RB 867.10.xxPOSITRACK BSA 505 RBP 868.50.xx255 to 680 2x belt width 15000 1300 -40 to +80 -40 to +65 9.0 15* In code numbers xx corresponds with the belt width (A), starting with 12 for 255 mm, 13 for 340 mm and so on with 85 mm increments up to680 mm; wider belts available upon request. See also page 206.STANDARD POSITRACK LUGS ON BOTH SIDESCURVE GUIDING PROFILE FOR 505PIN RETENTION CLIPS FOR EASY (DIS)ASSEMBLYThe curve guiding profile for the 505 has a standard length of 2 meters; it is made of MCC 3500 special polyamide, code nr. 800.00.01, orMCC 3600 polyester for direct food contact, code nr. 800.00.13.197
Page 1:
PRODUCT CATALOGUE REXNORD ® / MCC
Page 4:
The companyThe industries servedRex
Page 9 and 10:
STEEL TABLETOP CHAINSPROGRAMMESteel
Page 11 and 12:
STEEL TABLETOP CHAINSpage 55, 56,57
Page 13 and 14:
STEEL TABLETOP CHAINSpage 61page 20
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
STEEL TABLETOP CHAINS WITH RUBBER T
Page 23 and 24:
Page 25 and 26:
Page 28 and 29:
PLASTIC TABLETOP CHAINSpage 58, 59,
Page 30 and 31:
PLASTIC TABLETOP CHAINSpage 62, 63,
Page 32 and 33:
PLASTIC TABLETOP CHAINSpage 104page
Page 34 and 35:
Page 36 and 37:
Page 38 and 39:
Page 40 and 41:
PLASTIC SPECIAL CHAINSpage 73page 1
Page 42 and 43:
PLASTIC TABLETOP CHAINS WITH RUBBER
Page 44 and 45:
Page 46 and 47:
Page 48 and 49:
PLASTIC TABLETOP LBP CHAINSpage 60,
Page 50 and 51:
PLASTIC TABLETOP LBP CHAINSpage 122
Page 52 and 53:
CHAINBELTSpage 119page 72FLUSH GRID
Page 54 and 55:
CHAINBELTS20minpage 12183.84561.570
Page 56 and 57:
SPROCKETS FOR TABLETOP CHAINSSprock
Page 58 and 59:
Page 60 and 61:
Page 62:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
CORNER DISCS FOR TABLETOP CHAINSCor
Page 75 and 76:
MULTIFLEX AND CASE CONVEYOR CHAINSP
Page 77 and 78:
MULTIFLEX CHAINSpage 83page 2071757
Page 79 and 80:
MULTIFLEX CHAINSpage 82, 83page 207
Page 81 and 82:
MULTIFLEX CHAINSpage 82, 83page 207
Page 83 and 84:
SPROCKETS FOR MULTIFLEX CHAINSSproc
Page 85 and 86:
PLASTIC CASE CONVEYOR CHAINSpage 89
Page 87 and 88:
PLASTIC CASE CONVEYOR CHAINSpage 89
Page 89 and 90:
SPROCKETS FOR CASE CONVEYOR CHAINST
Page 91 and 92:
PROGRAMMEPLATE TOP AND GRIPPER CHAI
Page 93 and 94:
PLATE TOP CHAINSpage 208STRAIGHT RU
Page 95 and 96:
PLATE TOP CHAINSpage 123page 208SID
Page 97 and 98:
PLATE TOP GRIPPER CHAINSpage 123pag
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
CURVES AND STRAIGHT TRACKSMagnetfle
Page 105 and 106:
MAGNETFLEX CURVESpage 16, 24page 31
Page 107 and 108:
Page 109 and 110:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
MAGNETFLEX CURVESpage 49page 209MAG
Page 120 and 121:
MAGNETFLEX CURVESpage 53page 209MAG
Page 122 and 123:
TAB CURVESpage 38, 45,50, 51page 20
Page 124 and 125:
TAB CURVESpage 78, 80, 81page 209KT
Page 126 and 127:
BEVEL CURVESpage 33page 209KSU 200F
Page 128 and 129:
OVERVIEW REXNORD MATTOP MPitchinch
Page 130 and 131:
PLASTIC MODULAR BELTSWith a large v
Page 132 and 133:
The 500-series 1 ⁄2-inch pitch be
Page 134 and 135:
510-SERIES MODULAR BELTSThe 510-ser
Page 136 and 137:
The 1500-series 15 mm pitch belt he
Page 138 and 139:
1500-SERIESpage 141page 208FLUSH GR
Page 140 and 141:
1500-SERIESpage 141page 208FLUSH FL
Page 142 and 143:
The 8500-series 3 ⁄4-inch pitch b
Page 144 and 145:
8500-SERIESpage 145page 208PERFORAT
Page 146 and 147: The 5930-series 3 ⁄4-inch pitch b
Page 148 and 149: 5930-SERIESpage 149page 208VACUUM T
Page 150 and 151: The 1000-series 1-inch pitch belt c
Page 152 and 153: 1000-SERIESpage 156, 157page 208FLU
Page 154 and 155: 1000-SERIESpage 156, 157page 208RAI
Page 156 and 157: 1000-SERIESpage 156, 157page 208LBP
Page 158 and 159: The 1005-series 1-inch pitch heavy-
Page 160 and 161: 1005-SERIESpage 163Apage 208SUPERGR
Page 162 and 163: Page 163page 208LBP1005Assembly Bel
Page 164 and 165: The 1010-series 1-inch pitch belt i
Page 166 and 167: The 7700-series 1-inch pitch heavy-
Page 168 and 169: 7700-SERIESpage 169page 208PERFORAT
Page 170 and 171: The 6300-series 50 mm pitch hybrid
Page 172 and 173: 6390-SERIESpage 173page 208PERFORAT
Page 174 and 175: The 2000-series 2-inch pitch belt i
Page 176 and 177: 2000-SERIESpage 177, 178page 179RAI
Page 178 and 179: 2000-SERIESpage 176page 208CLICK-CO
Page 180 and 181: The 2010-series 2-inch pitch belts
Page 182 and 183: 2010-SERIESpage 183page 208TEXTURED
Page 184 and 185: 9200-SERIES FORTREX STAINLESS STEEL
Page 186 and 187: 9200-SERIESpage 185page 209CLASSICF
Page 188 and 189: The 2500-series 2 1 ⁄2-inch pitch
Page 190 and 191: The 6990-series 2 1 ⁄4-inch pitch
Page 192 and 193: 6990-SERIESSprocket type Code nr. N
Page 194 and 195: 3120-SERIES76.2 (3")page 195page 20
Page 198 and 199: EF505-SERIESSprocket Code nr. Nr. B
Page 200 and 201: 1200-SERIESpage 203page 203page 208
Page 206 and 207: TABLE BELT WIDTHSBelt seriesStandar
Page 208 and 209: ProductMaterial beltMATERIALSPLASTI
Page 210 and 211: Chain page Belt page Sprocket page
show all

plastic tabletop chains - FB Kjeder

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?