Pricing Guide for Horizontal Above NEMA Motors - Siemens Industry ...

More documents

Recommendations

Info

Pricing Guide for Horizontal Above NEMA Motors ANSP-60000-1112Section 1Part GeneralPage 2Date 11/12General InformationAll ratings in this price guide are designed for the following; Horizontal Mounting 3 phase Class F insulation Service factor of 1.0 Maximum temperature rise of 80 degrees C by resistance at 1.0 service factor Maximum 40 degrees C ambient Altitude of 3300 feet or less Direct connection to a typical centrifugal load with rated voltage and frequency applied at themotor terminals and a load inertia value equal to or less than NEMA value for the rating. Also,during accelerating period, connected load torque shall be equal to, or less than, a torque whichvaries as square of the speed and is equal to 100% of full-load torque at rated speed.Frame sizes are estimated and are subject to change without notice. Frame sizes may have a suffix orcombination of suffixes dependent upon enclosure, bearings, and/or features; D = Flanged. Indicates that motor is to be supplied with a D-flanged bearing housing. S = Short shaft. Indicates motor is to be supplied with Siemens standard short shaft extension fordirect connection except on 680 frame series where no suffix is used. Y = Special mounting. Indicates motor is to be supplied with non-standard mounting dimensions. Z = Special shaft. Indicates motor is to be supplied with non-standard or special shaft dimensions. No Suffix = Indicates that motor is to be supplied with a Siemens standard long shaft extensionexcept on 680 & 800 frame series. The long shaft is provided if Belt Drive modification is madefrom the Modification & Accessories Section.Some 680 frame ratings can be supplied with grease lubricated ball bearings. Refer exact requirementsto factory for price and availability.Lead Times will be per the latest issue of the Norwood Product Lead Times document ANMC- 70000-xxxx.
Pricing Guide for Horizontal Above NEMA Motors ANSP-60000-1112Section 1Part EnclPage 3Date 11/12Enclosures – Designed To Meet All Application And Environmental NeedsHorizontal Drip Proof / Weather Protected I (Type CG) / IC01 / IP23Meets or exceeds industry standards for NEMA WP-type machines. Best suited for indoor applications wherenot exposed to extreme ambient conditions. Available through 10,000 HP.Horizontal Drip Proof / Weather Protected II (Type CGII) / IC01 / IP24Meets or exceeds industry standards for NEMA WPII-type machines. Specifically designed for outdoorapplications where motor is not likely to be protected by other structures. Available through 18,000 HP.Totally Enclosed Fan Cooled(Type CZ, CGZ, 1LA4) / IC411 / IP54-IP55Designed for indoor and outdoor applicationswhere internal parts must be protected fromadverse ambient conditions. Utilizes coolingfins on all four quadrants of yoke andhousings. Available through 3,000 HP.Totally Enclosed Air-to-Air Cooled(Type CAZ) / IC611 / IP54Designed for indoor and outdoor applications whereinternal parts must be protected from adverseambient conditions. Utilizes air-to-air tube-type heatexchangers. Available through 14,000 HP.
Page 1 and 2: Pricing Guide for HorizontalAboveNE
Page 3: Pricing Guide for Horizontal Above
Page 7 and 8: Pricing Guide for Horizontal Above
Page 54 and 55:
Pricing Guide for Horizontal Above
Page 56 and 57:
Page 58 and 59:
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
show all

Pricing Guide for Horizontal Above NEMA Motors - Siemens Industry ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?