Lista mensal documentos normativos - IPQ

DOCUMENTOSnormativosPolymer modified bituminous thick coatings forwaterproofing Determination of dimensional stability athigh temperatureData Limite: 2011-01-12TC 361prEN 15819:2010Polymer modified bituminous thick coatings forwaterproofing Reduction of the thickness of the layerwhen fully driedData Limite: 2011-01-12TC 361prEN 15820:2010Polymer modified bituminous thick coatings forwaterproofing Determination of watertightnessData Limite: 2011-01-12TC 377prEN 16154:2010Air Traffic Management Software assurance levelsData Limite: 2011-02-16TC 385prEN 16118:2010Sheltered housing Requirements for services for elderlypeople provided in a sheltered housing schemeData Limite: 2010-11-03TC CSF01prEN ISO 10628-2:2010Diagrams for the chemical and petrochemical industryPart 2: Graphical symbols(ISO/DIS 10628-2:2010)Data Limite: 2010-12-15TC CST01prEN ISO 12217-2:2010Small craft Stability and buoyancy assessment andcategorization Part 2: Sailing boats of hull length greaterthan or equal to 6 m(ISO/DIS 12217-2:2010)Data Limite: 2010-10-06TC CST01prEN ISO 12217-3:2010Small craft Stability and buoyancy assessment andcategorization Part 3: Boats of hull length less than 6 m(ISO/DIS 12217-3:2010)Data Limite: 2010-10-06TC CSB02EN ISO 11600:2003 /prA 1:2010Building construction Jointing products Classificationand requirements for sealants(ISO 11600:2002/DAM 1:2010)Data Limite: 2010-10-06TC CSM11prEN ISO 3927:2010Metallic powders, excluding powders for hardmetalsDetermination of compressibility in uniaxialcompression(ISO/FDIS 3927:2010)Data Limite: 2010-12-09TC CSF20prEN ISO 19011:2010Guidelines for auditing management systems(ISO/DIS 19011:2010)Data Limite: 2010-11-17TC CSN21prEN ISO 6145-5:2010Publicação oficial do IPQ, enquanto Organismo Nacional de NormalizaçãoGas analysis Preparation of calibration gas mixturesusing dynamic volumetric methods Part 5: Capillarycalibration devices(ISO 6145-5:2009)Data Limite: 2010-11-10TC CSN21prEN ISO 6145-7:2010Gas analysis Preparation of calibration gas mixturesusing dynamic volumetric methods Part 7: Thermalmassflow controllers(ISO 6145-7:2009)Data Limite: 2010-11-10TC CSN21prEN ISO 6145-9:2010Gas analysis Preparation of calibration gas mixturesusing dynamic volumetric methods Part 9: Saturationmethod(ISO 6145-9:2009)Data Limite: 2010-11-10TC CSS26prEN ISO 14051:2010Environmental management Material flow costaccounting General framework(ISO/DIS 14051:2010)Data Limite: 2010-10-27TC ECISS/29prEN ISO 10893-12:2010Non-destructive testing of steel tubes Part 12:Automated full peripheral ultrasonic thickness testingof seamless and welded (except submerged arc-welded)steel tubes (ISO/FDIS 10893-12:2010)Data Limite: 2010-11-09TC ECISS/109prEN 10209:2010Cold rolled low carbon steel flat products for vitreousenamellingTechnical delivery conditionsData Limite: 2010-12-08TC ECISS/110prEN 10352:2010Stainless steel plumbing fittings Fittings with press endsfor metallic tubesData Limite: 2011-02-16TC ECISS/110prEN ISO 10893-1:2010Non-destructive testing of steel tubes Part 1: Automatedelectromagnetic testing of seamless and welded (exceptsubmerged arc-welded) steel tubes for the verification ofhydraulic leaktightness instead of the hydrostatic test(ISO/FDIS 10893-1:2010)Data Limite: 2010-11-09TC ECISS/110prEN ISO 10893-2:2010Non-destructive testing of steel tubes Part 2: Automatededdy current testing of seamless and welded (exceptsubmerged arc-welded) steel tubes for the detection ofimperfections (ISO/FDIS 10893-2:2010)Data Limite: 2010-11-09TC ECISS/110prEN ISO 10893-3:2010Non-destructive testing of steel tubes Part 3: Automatedfull peripheral flux leakage testing of seamless andwelded (except submerged arc-welded) ferromagneticsteel tubes for the detection of longitudinal andtransverse imperfections (ISO/FDIS 10893-3:2010)Lista mensal ▪ documentos normativos imp DNOR-01-06 47 14 Outubro 2010