VENTURA 150 DELUXE INSTALLATION MANUAL

More documents

Recommendations

Info

The Z-Brane is a revolutionary product which incorporates Z-Guard High Voltage Capacitivetechnology into the membrane pressure vessel. Always active, the Z-Brane createsan environment that is unfriendly to bio-film and bacteria. The Z technology also assistsin the prevention of scale formation on the membrane surfaces. The Z-Brane allowsthe system to be shut down or decommissioned for extended periods of time withoutchemicals or preservatives. The Z-Brane will not prevent freezing so that in cold climatespropylene glycol is still required.The Z-Brane system is integrated with the watermaker unit and only requires continuous12Vor 24V DC power to be operative. The installation of the Z-Brane only consists ofwiring the power supply to a continuous source The Z-brane power supply can toleratevoltages between 10V and 28V DC.NOTE: There is no reason to open the transformer enclosure. DO NOT service thisunit without disconnecting the power source! There may be high voltage present.It is recommended that the Z-Brane be connected to a discreet continuous power source.The power must be on during the time that the system is operation and during the time theZ-Brane is used for membrane storage. If the power is obtained from the MPC then theMPC must be powered up at all times during storage. This may not be desirable.Fuse the power at the source with a 5 amp fuse or circuit breaker.Red is Positive (+) , Black is Ground (-)Z-Brane Power Harness34
OperationDuring normal operation the red LED should be on. Power needs to be supplied to the Z-Brane unit for as long as you wish to have the bio-fouling and scale protection. We recommendthat your watermaker be flushed after each use not only to protect the membrane but toprevent corrosion in the feed water system. To achieve full effectiveness thoroughly freshwater flush the watermaker several times before leaving the vessel.The Z-Brane may be de-powered if the system is stored with chemicals or winterized withglycol.Power on LEDHigh VoltageconnectorDO NOT DISCONNECTOR SPLICE ANY OF THEHIGH VOLTAGE WIRING!Contact the factory ifmodifications are required.35
Page 1: VENTURA 150 DELUXEINSTALLATION MANU
Page 5 and 6: Getting StartedUnpack the system an
Page 7 and 8: Ventura 150 Deluxe PlumbingBrine Di
Page 9 and 10: BodyO-ringSpacerGrab RingNutTubingS
Page 11 and 12: Spectra High Pressure Tube Fitting
Page 13 and 14: Feed Pump RelocationIf you do not h
Page 15 and 16: Ventura Deluxe Dry Testing With Art
Page 17 and 18: Long Term Storage ProceduresWaterma
Page 19 and 20: Pickling and Winterizing with Antif
Page 21 and 22: The Membranes• The membranes need
Page 23 and 24: Suggested SparesShort term cruising
Page 25 and 26: MISC-1 DWYER FLOW METER SERVICEThe
Page 27 and 28: OP-3 CHEMICALS 101Spectra Systems u
Page 30 and 31: MISC-3 ACCUMULATOR PRESSUREAll Spec
Page 32 and 33: SF-2 ADJUST SHURFLO PRESSURE SWITCH
Page 36 and 37: Part Numbers3/8 NPT Quick Disc. Bod
Page 38 and 39: PART NUMBERSPRODUCT WATERSAMPLING V
Page 40 and 41: 5/16"-3 1/4" SS AH BoltsHD-CPS-5/16
Page 42: S.S compressionfittingsPL-MTS-3/8X1

VENTURA 150 DELUXE INSTALLATION MANUAL

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?