Download Commander II Instruction Manual PDF file

More documents

Recommendations

Info

Installation Step 3Attach the Rail to the Header Bracket• Position the opener on the garage floor below the headerbracket. Use packing material as a protective base. NOTE: If thedoor spring is in the way you’ll need help. Have someone holdthe opener securely on a temporary support to allow the rail toclear the spring.• Position the rail bracket against the header bracket.• Align the bracket holes and join with a clevis pin as shown.• Insert a ring fastener to secure.Header WallHeader BracketRail BracketRailHeader BracketRing FastenerSpacerGarageDoorClevis Pin5/16"x2-3/4"SpacerRailBracketRailOpener Carton orTemporarySupportHARDWARE SHOWN ACTUAL SIZEClevis Pin5/16"x2-3/4" Ring Fastener Spacer10
Installation Step 4Install The Protector System ®The safety reversing sensor must be connected and alignedcorrectly before the garage door opener will move in the downdirection.IMPORTANT INFORMATION ABOUT THE SAFETY REVERSINGSENSORSWhen properly connected and aligned, the sensor will detect anobstacle in the path of its electronic beam. The sending eye (withan amber indicator light) transmits an invisible light beam to thereceiving eye (with a green indicator light). If an obstructionbreaks the light beam while the door is closing, the door will stopand reverse to full open position, and the opener lights will flash10 times.The units must be installed inside the garage so that the sendingand receiving eyes face each other across the door, no more than6" (15 cm) above the floor. Either can be installed on the left orright of the door as long as the sun never shines directly into thereceiving eye lens.The mounting brackets are designed to clip onto the track ofsectional garage doors without additional hardware.Be sure power is not connected to the garage door openerBEFORE installing the safety reversing sensor.To prevent SERIOUS INJURY OR DEATH from a closinggarage door:• Correctly connect and align the safety reversing sensor. Thisrequired safety device MUST NOT be disabled.• Install the safety reversing sensor so beam is NO HIGHERthan 6" (15 cm) above garage floor.If it is necessary to mount the units on the wall, the brackets mustbe securely fastened to a solid surface such as the wall framing.Extension brackets (see accessories) are available if needed. Ifinstalling in masonry construction, add a piece of wood at eachlocation to avoid drilling extra holes in masonry if repositioning isnecessary.The invisible light beam path must be unobstructed. No part of thegarage door (or door tracks, springs, hinges, rollers or otherhardware) may interrupt the beam while the door is closing.Safety Reversing Sensor6" (15 cm) max. above floorInvisible Light BeamProtection AreaSafety Reversing Sensor6" (15 cm) max. above floorFacing the door from inside the garage11
Page 1 and 2: Raynor Garage Doors1101 E. River Ro
Page 3 and 4: 1Preparing your garage doorBefore y
Page 5 and 6: Carton InventoryYour garage door op
Page 7 and 8: WARNINGINSTALLATIONIMPORTANT INSTAL
Page 9: Installation Step 2Install the Head
Page 13 and 14: Mounting and Wiring the Safety Reve
Page 15 and 16: Installation Step 6Hang the OpenerT
Page 17 and 18: Installation Step 8Install the Ligh
Page 19 and 20: Installation Step 12Fasten the Door
Page 21 and 22: Installation Step 13Connect Door Ar
Page 23 and 24: Adjustment Step 1Adjust the UP and
Page 25 and 26: Adjustment Step 3Test the Safety Re
Page 27 and 28: Using the Wall-Mounted Door Control
Page 29 and 30: KGKGHaving a Problem?1. My door wil
Page 31 and 32: 91735KG91735KGLOCKLIGHTProgrammingN
Page 33 and 34: Repair PartsRail Assembly Parts5361
Page 35 and 36: SENDPASSREADYENROLLENROLLFAILRETRYC

Download Commander II Instruction Manual PDF file

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?