Specification for GE Magne-Blast Type AM Circuit Breakers

More documents

Recommendations

Info

Specification forGE Magne-Blast Type AMCircuit BreakersPowell Apparatus Service8550 Mosley Dr.Houston, TX 77075(713) 944-6900 - p(713) 948-4569 - fTESTINGSeller shall perform all design production and conformance tests on the new circuit breakerassemblies required in ANSI C37.09 and C37.59, Section 5. Racking tests per ANSI C37.20.2,if required to verify mechanical interfaces with the existing switchgear assembly for testpurposes.Test data from previous similar designs may be used for current design verification whenprovided in accordance with ANSI C37.59, Section 5.Certified test results may be submitted for acceptance in lieu of performance tests if vendor haspreviously completed design test on a breaker submitted for evaluation in accordance with thisspecifications requirements.SHIPPINGThe interior of all equipment shall be free of all foreign materials such as welding rod waste,mill scale, oil, grease or other deleterious material.In general all equipment and material shall be suitably crated boxed, or otherwise preparedfor shipment to prevent damage during handling, shipping, and storage. ALL openings shall beproperly protected to prevent the entrance of dirt or debris. It shall be the responsibility ofSeller to take any precautions required to reasonably ensure jobsite arrival of the equipment inan undamaged and satisfactory working condition.QUALITY ASSURANCESeller shall have a QA Program in effect at all times to verify that all items and services,including subcontracted items and services, comply with the requirements of the purchaseorder and its attachments.DEVIATIONS AND NON-CONFORMANCESAny departure from any requirement of this specification is considered a deviation ornonconformance. Examples include, physical defects in equipment, test failures, equipmentout-of-tolerance, or deviations from specification, inspection, or test procedures. No deviationor nonconformance shall be accepted until approved in writing by Purchaser.©2004 Powell Apparatus Service • All rights reserved.
Specification forGE Magne-Blast Type AMCircuit BreakersPowell Apparatus Service8550 Mosley Dr.Houston, TX 77075(713) 944-6900 - p(713) 948-4569 - fDOCUMENTATION BY SELLERInstruction ManualsSeller shall submit to purchaser two (2) complete, bound copies of the instruction manuals.In addition, one instruction manual shall be sent with the equipment to the site.Instruction manuals shall be applicable to the circuit breakers furnished and shall bespecifically identified as such.DrawingsDrawings shall be provided for new circuit breaker within four weeks (4) after signing thePurchase Order. Seller shall furnish a mylar reproducible or AutoCAD file on a floppy disk andtwo prints for each drawing. Drawings shall show the following:1) Physical outlines showing the overall size and weight of the new circuit breaker andthe interrelationship of the various breaker components2) Complete circuit breaker wiring diagrams3) Details of any modifications to the switchgear assembly to be make by Purchaser.Test ReportsTest reports shall be prepared for all tests required by this specification. Test reports shallbe certified by Seller’s representative to be accurate and complete. Test reports shall besubmitted to Purchaser upon completion of testing and prior to shipment of equipment.WARRANTYThe Replacement vacuum circuit breaker shall be warranted to be free of defects in materialsand workmanship for a period of 12 months from the date of equipment energization or18 months form shipment, whichever occurs first. Any defect in the design, materials orworkmanship discovered within this period shall be repaired or replaced without cost to thepurchaser, including shipping costs.©2004 Powell Apparatus Service • All rights reserved.
Page 1 and 2: Specification forGE Magne-Blast Typ
Page 3 and 4: Specification forGE Magne-Blast Typ
Page 5: Specification forGE Magne-Blast Typ

Specification for GE Magne-Blast Type AM Circuit Breakers

Create successful ePaper yourself

Delete template?

Save as template?