Triton T60si - Faucets, Showers, Bathroom, Kitchen, More.

More documents

Recommendations

Info

<strong>T60si</strong>Fig. 6Fig. 7Fig. 8Fig. 9120 mmINSTALLATION – plumbingPlumbing to precede wiring.Unscrew the two top and one bottom retainingscrews (fig.6) and lift the cover from thebackplate.For ease of installation, all pipe work and electricalwiring should be positioned in place, ready forfinal connection, before fitting the backplate unitto the wall.Use the backplate as a template and mark outlineon the wall so that pipework can be cut to suit.Three entry positions – top, bottom or back, areavailable for the pipework and cable.NOTE: Deviations from the designated entrypoints will invalidate product approvals.Fit a finishing trim in either the top or bottom ofthe backplate (fig.7) depending upon whethertop or bottom entry has been chosen.If installing a feed pipe from the top, as a guidefor cutting the pipe, the centres are 120mm(fig.8).Where pipework enters from the back or bottom,note the centre of the inlet valve to the wallsurface is 20mm (fig.9).Having decided the entry positions, cable andpipework must be installed prior to fixing thebackplate to the wall.WARNING: The outlet of the shower acts as avent and must not be connected to anythingother than the hose and sprayhead supplied.DO NOT use jointing compounds on any pipefittings for the installation.DO NOT use soldered fittings within the vicinity ofthe shower unit.NOTE: An additional stopvalve (complying withWater Regulations) must be fitted in the mainswater supply to the shower as an independentmeans of isolating the water supply shouldmaintenance or servicing be necessary.Turn off water supply either at the mainsstopvalve or the isolating stopvalve.15mm copper or stainless steel pipe may be beused and all pipework and fittings can be fixedand tightened except the final joint to the showerinlet.20 mm8
<strong>T60si</strong>A 15mm x 15mm straight coupler or elbow fitting(fig.10) must be used for connection to theshower inlet. NOTE: The shower inlet connectionis designed to enter a compression fitting only.DO NOT use push fit connectors as fullengagement cannot be guaranteed.Ensure the plastic filter (fig.11) is inserted in thesupply pipe before connection. This helps toprevent ingress of debris.If entry is from the rear, the conex nut fitting willbe partially behind the surface of the wall (fig.9).This area must be left clear when plastering overthe pipework in order to make the nut accessiblefor future adjustments.DO NOT use excessive force when making theseconnections.When all pipework is complete, temporarily placethe backplate unit onto the pipework and markholes on the wall for the fixing screws (fig.12).Remove the backplate and drill and plug the holesto suit fixing screws supplied. (The wallplugsprovided are suitable for most brick walls – use anappropriate masonry drill, but if the wall isplasterboard or a soft building block, you mustuse special wallplugs and an appropriate drill bitobtainable from most hardware stores).Important: Before completing the connection ofthe water supply to the inlet of the shower, and incompliance with Water Regulations, flush out thepipework to remove all swarf and system debris.This can be achieved by connecting a hose to thepipework and turning on the mains water supplylong enough to clear the debris to waste.After flushing out, turn off the mains watersupply, re-position the unit onto the pipeworkand tighten final connection at shower inlet.Turn on the water supply and check for watertightness.Position the backplate onto the wall and screwthe top and bottom fixing screws into position.Ensure the unit is square on the wall and tightenthe two fixing screws.FilterElbow orStraightcouplerFig.10Fig.11Fig.129
Page 1 and 2: . T60si electric shower .Installati
Page 3 and 4: T60siPLEASE READ THIS IMPORTANT SAF
Page 5 and 6: T60siKEY TO MAIN COMPONENTS(inside
Page 7 and 8: T60siELECTRICAL REQUIREMENTS5.1 All
Page 9: T60sior shower tray, then a double
Page 13 and 14: T60siREPLACING THE COVERThe power s
Page 15 and 16: T60siFITTING THE HOSE AND SPRAYHEAD
Page 17 and 18: T60siOPERATING THE SHOWERNOTE: Ensu
Page 19 and 20: T60siOPERATING FUNCTIONSPower indic
Page 21 and 22: T60siSPARE PARTSRef DescriptionPart
Page 23 and 24: T60siTemperature / flow rate graph
Page 25 and 26: T60siFAULT FINDING (continued)Probl
Page 27 and 28: UKASQUALITYMANAGEMENT003

Triton T60si - Faucets, Showers, Bathroom, Kitchen, More.

Create successful ePaper yourself

Delete template?

Save as template?