Infinity Operations Manual (15441, 15641, 15253, 15653) - Whip Mix

More documents

Recommendations

Info

ERROR CODESNOTE: “Beeps” occur when the Error Code appears on the Main Displayerrorcode DESCRIPTION PROBABLE CAUSEEr 1Er 2INVALID ENTRYERROR: STAGE,HEAT RATE andTEMP lights flashTABLETTEMPERATURECALIBRATIONERROROccurs when the HEAT RATE is set to COOL but the TEMP of that stage ishigher than the TEMP of the prior stage (should be heating). This will occurwhen a program is already running and a parameter was edited in process.Occurs when the temperature on the display is outside the allowable rangeat the time the user pressed the ENTER / REVIEW keys simultaneously to setthe <strong>Infinity</strong> calibration temperature to 1500°F. If this occurs and is not anoperator error, it indicates that there is a problem with the thermocouple orthe PC board. Press ENTER / REVIEW to turn off the error indication andcontinue with the program. Press START / STOP to end the program.Er 3ELECTRONICSMALFUNCTIONOccurs when PC board hardware malfunctions.Er 4OPENTHERMOCOUPLEOccurs if the thermocouple is open or the connecting wire(s) are broken ordisconnected from the terminal board.Er 5REVERSEDTHERMOCOUPLEOccurs if the thermocouple extension wires have been connected backwardsto the terminals on the printed circuit board. The error will be detected 5minutes after heating program started. This error will also occur if theprogram is started and the chamber door is kept open for 5 minutes or thetriac is defective, the heater plates are defective or there is a problem withthe main PC board.17
ERROR CODESerrorcode DESCRIPTION PROBABLE CAUSEEr 6Er 7SHORTEDTHERMOCOUPLEOR DEFECTIVEHEATER PLATESTHERMALRUNAWAYOccurs if the thermocouple wires are shorted or the heater plates aredefective causing <strong>Infinity</strong> to achieve a HEAT RATE of less than 6% of themaximum attainable HEAT RATE with full power applied to the heaterplates for 5 minutes. This error will also occur if a program is runningand the door is kept open for more than 5 minutes or the triac or theMain PC board developed a problem during a burnout process.Occurs when the temperature has exceeded 2015°F (1102°C) for 1minute if the highest temperature programmed was less than 2000°F(1093°C). This also occurs when the temperature has exceeded2050°F (1121°C) for 1 minute if the highest temperature programmedwas 2000°F (1093°C) or higher.Flashing99:99 whenNIGHTTIME(DELAYSTART) ispressedduring aprograminvalid entryerror while aprogram isrunningOccurs when the HEAT RATE in STAGE 2, 3 or 4 is set to “COOL” butthe corresponding TEMP is entered to heat to a higher temperaturethan the previous stage.18
Page 1: InfinityTMBurnout FurnacesOPERATOR
Page 6 and 7: key parts identification and explan
Page 8 and 9: installationunpack and set-up1. Unp
Page 10: OPERATIONprogram and operate - one
Page 14 and 15: OPERATIONreview a program (figure 1
Page 16 and 17: OPERATIONSample one stage program(T
Page 21 and 22: SERVICE6. When the tablet begins to
Page 23 and 24: Figure 4INFINITY WITH UPPER REAR PA
Page 25 and 26: Figure 5INFINITY WITH FRONT PANEL /
Page 27 and 28: FIELD SERVICEREPLACEMENT OF THE TRI
Page 29 and 30: SPARE PARTS LISTPARTS FOR INFINITY
Page 31 and 32: PROGRAM CARD FORMSProgram #Metal(s)

Infinity Operations Manual (15441, 15641, 15253, 15653) - Whip Mix

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?