Heat-Tracing Systems for Hazardous Division 1 Locations

More documents

Recommendations

Info

5.6 HAK-C-100 Connection Kit Installation1. Fasten universal mounting bracket (UMB) on pipe, using appropriate size stainless steel pipe strap,or fabricate and locate suitable mounting plate <strong>for</strong> junction box within 24 inches of desiredconnection on pipe.Threaded inserts2. Thread compression gland half with threaded inserts into end of sealing fitting nearest verticalplug. Disassemble union. Thread female half of union onto nipple. Thread nipple into other end ofsealing fitting nearest angled plug.3. Thread male half of union into box entry. Assemble union halves together. Mount box on bracket.27
Cut18"WARNING: Correct grommet must be used<strong>for</strong> heating cable being installed orelectrical hazard could result.4. Corrugated tubing is provided. Measure length required to transition from compression gland topipe surface, and cut to length.WARNING: Fire hazard.Do not cut braid or bus wires. Damagedheating cable must be replaced.12"Do NotCut Braid5. Being careful not to damage braid, score around outer heating cable jacket 12 inches from theend that extends out of the junction box. Score from this point to end of heating cable. Removeouter jacket.28
Page 1 and 2: RHeat-Tracing Systems forHazardous
Page 3 and 4: Table of Contents1. Introduction1.1
Page 5 and 6: 1.4 Electrical Connections and Comp
Page 7 and 8: Note: Publication NFPA 325 gives ig
Page 9 and 10: Step 7. Determine the heating cable
Page 11 and 12: Table 3. Pipe Heat Loss*Temperature
Page 13 and 14: Graph 1. Thermal Output Ratings for
Page 15 and 16: 3. Electrical DesignNote: Ground-fa
Page 17 and 18: Table 5. Circuit Breaker Selection
Page 19 and 20: 4.2 Core SealingThere are two appro
Page 21 and 22: F MA PROVED(S E NOTE 1)RLISTED3 5S
Page 23 and 24: Heating cable minimum bend radius:T
Page 25 and 26: 5.3.7 Valve (typical)Glass tape(typ
Page 27 and 28: 5.3.10 Pipe Bar Hanger;;Bar hanger;
Page 29: 5.5 HAK-C-100 Connection Kit Descri
Page 33 and 34: 1/4"3/4"9. For solid-core heating c
Page 35 and 36: 14. Fasten terminal to ground lug i
Page 37 and 38: Packing fiber18. Using packing fibe
Page 39 and 40: 5.9 Power Supply and Electrical Pro
Page 41 and 42: Test ATest B+ -Figure 2 . Postinsul
Page 43 and 44: 6.2 TroubleshootingSymptoms Probabl
Page 45 and 46: 7. Answers to Frequently Asked Ques
Page 47 and 48: What happens if the end user does n
Page 49 and 50: Appendix B: Alternate Voltage Adjus
Page 51 and 52: Appendix D: Heat-Shrink Core Sealer
Page 53 and 54: 8. Slide on black heat-shrinkable t
Page 55 and 56: Appendix F: FM Required Division 1
Page 57 and 58: Appendix H: BTV Heating Cable Selec
Page 59 and 60: 56Material Group °F °CCyclohexano
Page 61 and 62: Material Group °F °CNitroethane C

Heat-Tracing Systems for Hazardous Division 1 Locations

Create successful ePaper yourself

Delete template?

Save as template?