Manual Unheated - Applications for 1K High Viscosity Products

More documents

Recommendations

Info

EXTRUSION UNIT 82.216TWIN POST RAM(200 LITERS DRUM)The 82.216 pump is specially designed for pumping viscous materials. KREMLINREXSON equipment can process a wide range of materials including oils,greases, adhesives and sealants.This equipment has proved itself over the years to be strong and reliable andcan process products up to 1 million centipoises depending on specifi cation.The system pumps directly from the original material container and is used on200 liter pails (interior diameter 571 mm).The modular conception allows you to select an extrusion system comprisingof a pump, elevator, follower plate, gun and hoses + optional extras includingfi lter, regulator to suit your application.Equipment compliant with ATEX Directive.FEATURESModular designAir motor design enables precise controlDirect pumping from 200 lts drumShovel pump technologyChoice of double seal on follower platePneumatic driven pumpBENEFITSWide range of options available to suitmost applicationsThe unique air motor designensures a constant controllled fl ow ratewith low noise and minimum icing riskClean wipe of the material drum savingmaterialsCan be used with a wide range ofmaterialsRecommended for high viscosity andmoisture-sensitive materialsSafe for use with solvents and otherfl ammable materials141 (4.0)124 (3.5)106 (3.0)88.3 (2.5)70.6 (2.0)52.9 (1.5)35.3 (1.0)17.6 (0.5)Motor air consumption(m 3 /min.) (Cubic feet/min).6 bar - 87 psi4 bar - 58 psi2 bar - 29 psi0 10 20 30 40 50 60Pump cycles per minuteSPECIFICATIONSPressure ratio 82/1Motor type 9000Fluid volume per cycle (cc) 216Free flow rate at 60 cycles (L/mn) 12,9Fluid Output at 15 Cycles (l/mn) 3,3Air consumption (m 3 /h) at 30 cycles/mn at 4 bar 102Maximum air inlet pressure (bar) 6Maximum fluid pressure (bar) 492Maximum Fluid Temperature (°C) 60Seal packingsPTFE + PEWetted partsCarbon steelWeight (kg) - bare pump 62FITTINGSFitting Air Inlet F 3/4'' G (1)(1) Recommended air supply hose diameter 1/2"Fluid Inlet Ø 105Fluid OutletF 1'' G50GUIDE KREMLIN FR GB DER OK.indd 50 17/05/11 09:52
EXTRUSION UNIT 82.216 TWIN POST RAM(200 LITERS DRUM)+COMPLETE PUMP UNITDescriptionTWIN POST RAM FOR 82.216 PUMP - PTFE/PE SEALSDescriptionFILTER AND REGULATOR OPTIONSDescriptionMANUAL GUN AND ACCESSORIESDescription+++Part number82.216 extrusion pump with PTFE/PE seals ( II2G IIB T3) 151.070.500Part numberDouble post ram with air control for 200 liters drums and centering/hold-down clamps ( II2Gc) 151.090.500Option : Runaway valve - to be fi tted on the air inlet (3/4" NPT) 151.098.070Option : Pneumatic two-hand safety control 151.098.050Option : Pneumatic low level alarm for 200 liters drums 151.098.020Drum roller unit for 200 litres drum 151.098.100FOLLOWER PLATES FOR 82.216 PUMPDescriptionTypeFollower plate Ø(mm)Follower plate Ø (inches) Part numberFollower plate - Nitrile Single fl at seal 571 22,48 151.100.500Follower plate PTFE coated-EPDMDouble seal O'ring 571 22,48 151.102.600Part numberOption A : Regulator with fi tting and mounting accessories (plate, fi ttings, hose...) 151.260.985Option B : Filter with fi tting and mounting accessories (plate, fi ttings, hose...) 151.260.986Option C : Filter and regulator with fi tting and mounting accessories (plate, fi ttings, hose...) 151.260.987HOSES AND FITTINGS KITSDescriptionØ 1/2" PTFE hose 7/8" JIC fi tting, lg 5m and PTFE Ø 3/8" whip end 3/4" JIC fi tting, lg 2mwith all required fi ttingsØ 3/4" PTFE hose 1" 1/16 JIC fi tting, lg 5m and PTFE Ø 3/8" whip end 3/4" JIC fi tting, lg2m with all required fi ttingsØ 1/2" PTFE hose 7/8" JIC fi tting, lg 10m and PTFE Ø 3/8" whip end 3/4" JIC fi tting, lg 2mwith all required fi ttingsØ 3/4" PTFE hose 1" 1/16 JIC fi tting, lg 10m and PTFE Ø 3/8" whip end 3/4" JIC fi tting, lg2m with all required fi ttings+DiameterFluid hose(")Length(m)Part number1/2 + 3/8 7 151.260.9813/4 + 3/8 7 151.260.9831/2 + 3/8 12 151.260.9823/4 + 3/8 12 151.260.984Part numberExtrusion gun 500 bar (equipped) 151.110.600Plastic disposable nozzles (x10) 151.110.290+C1351GUIDE KREMLIN FR GB DER OK.indd 51 17/05/11 09:52
Page 3: SALES GUIDEHIGH VISCOSITY PRODUCTSO
Page 6 and 7: EXTRUSION UNIT 60.60 SINGLE POST RA
Page 8 and 9: EXTRUSION UNIT 60.60MINI TWIN POST
Page 10 and 11: EXTRUSION UNIT 60.60 MINI TWIN POST
Page 12 and 13: EXTRUSION UNIT 60.60 TWIN POST RAM(
Page 15 and 16: NOTESC313GUIDE KREMLIN FR GB DER OK
Page 17 and 18: EXTRUSION UNIT 34.106 MINI TWIN POS
Page 19 and 20: NOTESC12C417GUIDE KREMLIN FR GB DER
Page 21 and 22: EXTRUSION UNIT 34.106 TWIN POST RAM
Page 43 and 44: NOTESC1041GUIDE KREMLIN FR GB DER O
Page 47 and 48: NOTESC11C345GUIDE KREMLIN FR GB DER
Page 51: NOTESC1249GUIDE KREMLIN FR GB DER O
Page 55 and 56: NOTESC1353GUIDE KREMLIN FR GB DER O
Page 57 and 58: MAIN FEATURES AND BENEFITS FOR CHOP
Page 59 and 60: THINGS TO KNOW ABOUT SELECTING AFOL
Page 61 and 62: NOTES59GUIDE KREMLIN FR GB DER OK.i
Page 63 and 64: PRACTICAL INFORMATION: VISCOSITIESU
Page 65 and 66: PRACTICAL INFORMATION:CHEMICAL COMP

Manual Unheated - Applications for 1K High Viscosity Products

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?