Manual Unheated - Applications for 1K High Viscosity Products

More documents

Recommendations

Info

THINGS TO KNOW ABOUT OPTIONALEQUIPMENTHeavy Duty cartsFor the single post and the mini twin post ram, we offer a heavy duty cart if youneed to be able to move your pump (except for 7000 and 9000 air motors).For the 200 lt twin post ram, the base is specially constructed so that it can betransported using either a pallet or a fork lift truck . The square box section preventsthe possibility of falling off the lifting forks whilst being transported.Two Hand Safety control Box Pneumatic (only for twin post ram units)Some customers may request an additional safety feature for the operator. Thetwo hand safety control box requires the operator to press two buttons simultaneouslyto raise and lower the pneumatic ram, thereby preventing any risk thatthe operator will trap his fingers between the drum and the follower plate.Low Level Stop with Alarm Pneumatic (only for twin post ram units)Some customers may require this included with the equipment. It can also beoffered at a later date. This is a very simple system to use which gives an audiblealarm when a preset level is reached in the material drum. It can also be usedto indicate to the operator that he only has enough material left in the drum tofinish the next job.Drum LoadingFor 200 lt systems we offer a modular roller base for ease of loading if you needto be able to move your pump.Materials filtersA fluid filter should be used when you need to filter/separate out impurities fromthe material. On high viscosity materials, this is more likely to be large lumps offiller or cured material.This is not as critical as with spray finishing since usually the nozzle diameter islarger in comparison with a spray tip, but unfiltered impurities may affect thequality of a bead or required finish.RegulatorsA regulator is needed when you want to control fluid pressure/flow rate, changefluid pressure to different values in a short time, dampen out pulsation onpump, change over and help prevent « snake head » effect on gun opening.However, be aware that this will not hide faults if there is a problem with thepump.Run-away valveFor safety and security reasons, there are some applications where it is prudentto fit a “run-away” valve. You would consider fitting a run-away valve on applicationswhere very high pressure is required.The run-away valve is set to normal working pressures, it senses normal presetairflow to the air motor but should a sudden increase in air flow go beyond itspreset value, then the run-away valve will close cutting the air supply to themotor. The pump run-away condition may be caused by a ruptured hose, orwhen the material drum is empty.58GUIDE KREMLIN FR GB DER OK.indd 58 17/05/11 09:52
NOTES59GUIDE KREMLIN FR GB DER OK.indd 59 17/05/11 09:52
Page 3:
SALES GUIDEHIGH VISCOSITY PRODUCTSO
Page 6 and 7:
EXTRUSION UNIT 60.60 SINGLE POST RA
Page 8 and 9:
EXTRUSION UNIT 60.60MINI TWIN POST
Page 10 and 11: EXTRUSION UNIT 60.60 MINI TWIN POST
Page 12 and 13: EXTRUSION UNIT 60.60 TWIN POST RAM(
Page 15 and 16: NOTESC313GUIDE KREMLIN FR GB DER OK
Page 17 and 18: EXTRUSION UNIT 34.106 MINI TWIN POS
Page 19 and 20: NOTESC12C417GUIDE KREMLIN FR GB DER
Page 21 and 22: EXTRUSION UNIT 34.106 TWIN POST RAM
Page 43 and 44: NOTESC1041GUIDE KREMLIN FR GB DER O
Page 47 and 48: NOTESC11C345GUIDE KREMLIN FR GB DER
Page 57 and 58: MAIN FEATURES AND BENEFITS FOR CHOP
Page 59: THINGS TO KNOW ABOUT SELECTING AFOL
Page 63 and 64: PRACTICAL INFORMATION: VISCOSITIESU
Page 65 and 66: PRACTICAL INFORMATION:CHEMICAL COMP
show all

Manual Unheated - Applications for 1K High Viscosity Products

Create successful ePaper yourself

Delete template?

Save as template?