RSE-1D1 - Ansaldo STS

More documents

Recommendations

Info

(Formerly known as Union Switch & Signal)Cardfiles (MicroLok II Applications)Rev. 4-11MicroLok II Half-Box (H.B.) CardfileHalf Box (H.B.) CardfileDescriptionThe MicroLok II Half Box (H.B.) cardfile is designed forwayside installations where mounting space is limited (e.g.equipment case) or a full size equipment house is notavailable. As such, it serves as a bridge between thelarge19-inch (48.25 cm) MicroLok II cardfiles and thecompact MicroLok Object Controller. The H.B. cardfile isonly 11 (27.9 cm) inches wide and is equipped withbrackets for wall or shelf mounting. Only six of the unit’s 10available slots require field configuration of I/O PCBs; theCPU and Power Supply/CPS boards’ location are fixed forall applications. The unit can also be outfitted with a frontattachedLocal Control Panel.The internal motherboard is extended above the cardfile toprovide a convenient panel to attach I/O PCB cables, serialcables, power input wiring and VCOR wiring. Six male-pinconnectors are provided on this panel to attach standard48-way MicroLok II cables (refer to RSE-1D2 for thesecables). Only the 96-pin cable for the 32/32 Non-Vital I/OPCB (N17061501) connector/cable assembly is notcompatible with the H.B. unit.Battery and VCOR wiring is attached via a 4-way Wagobrand connector in the upper right corner of the panel.Below this connector are three “D” style plugs forconnection of RS-485 or RS-232 serial communications linkwiring. The two RS-485 plugs are switch-selectable. Anoptional Serial-To-Ethernet Converter PCB can be installedto enable Internet-based remote communications. Thisboard is mounted inside the cardfile’s rear cover andprovides a top-accessible RJ-45 jack for Ethernetcommunications.Unit power is controlled by a standard 2-position toggleswitch, while the unit’s current draw is protected with a 10Amp fuse, also on the upper panel.SpecificationsPCB Design/Mounting:Unit Dimensions:Unit Mounting:Unit Weight (Approx.):Input Power:Starting Voltage:Fuse:Surge Protection:Power & VCOR Wiring:Total Field PCB Slots: 6Applicable I/O PCBs:Applicable II Cables:Serial Ports:Ethernet Port (Option):Operating Temperature:Humidity Limit:Standard EurocardSee above diagramShelf or wall (via brackets)7.5 lb. (3.4 kg)9.8 to 16.2 Vdc (12.0 Vdc nom.)11.2 Vdc (min.)10A (front panel mounted)5W, 16V Transzorb (5KP16A)Four cage clamp terminalsAll except 32/32 Non-Vital I/OPCB N17061501 (see RSE-1D2.2 and -1D2.3)All except those with 96-pinconnectors (see RSE-1D2)Two 9-pin “D” connectors: RS-485 (switch-selectable ports)One 25-pin “D” connector: RS-232One 9-pin “D” connector: RS-232RJ-45 jack-40°C to +70°C (-40°F to+158°F)95%, non-condensing, p. 6
Cardfiles (MicroLok II Applications)(Formerly known as Union Switch & Signal)Half Box 2X CardfileDescriptionThe MicroLok II Half-Box 2X (HB2X) Cardfile isderived from ASTS USA’s highly successfulHalf-Box cardfile (see catalog page 6). It can beconfigured as a multi-purpose vital and/or nonvitalmonitoring and control system for railroad ormass transit wayside interlocking applications,including railroad PTC configurations. This unithas 14 user-configurable slots and is designedfor wall or shelf mounting.The HB2X cardfile accommodates moststandard MicroLok II plug-in PCBs. Threedouble-width PCB slots are reserved for thePower Supply PCB in Slots 15 and 16. Slots 17and 18 are reserved for the vital CPU board,while slots 19 and 20 are held for the Genisys IIstyle non-vtial CPU board (when used). Theremaining 14 slots can take any standardMicroLok II I/O PCBs. Refer to the orderingtabulation on catalog page 9 for other PCBassignment information. The HB2X cardfile isequipped with an upper and a lowermotherboard. Connectors for external cablesare mounted on the front of the uppermotherboard.A 6-point, removable WAGO brand power connector ismounted on the front of the upper motherboard. Thisconnector is used for the battery input and VCOR coilwiring. One pin of this connector is routed internally tothe shutdown function of the Power Supply PCB. Thefunction allows the user to shut down the system usingan external power supply. The lower motherboard isequipped with a 6-pin WAGO brand connector to provideauxiliary (external power supply) power to the HB2X inplace of a Power Supply PCB.The HB2X cardfile contains three vital and/or three nonvitalcommunications ports for external communications.An additional port is used for internal communicationsbetween the non-vital and vital CPU PCBs, as requiredby the application. An optional Ethernet PCB(N17006202) can be plugged onto the rear of the HB2Xupper motherboard. The Ethernet port is accessible ontop of the cardfile when the Ethernet PCB is installed.SpecificationsPCB Design/Mounting:Unit Dimensions:Unit Mounting:Unit Weight:Standard EurocardSee above diagramShelf or wall (via brackets)22.25 lb. (10 kg)Input Power:Fuse:Surge Protection:Wiring Connections:Serial Ports:Ethernet Port (Option):Weight*:Operating Temperature:Humidity Limit:Rev. 4-119.8 to 16.2 Vdc (12.0 Vdcnom.)10A5W/16V TranzorbUpper: 6-point WAGO: Batt.input and VCOR wiringLower: 6-point WAGO:External power (in place ofPower Supply PCB)Two 9-pin “D” connectors:RS-485 (switch-selectableports)One 25-pin “D” connector:RS-232One 9-pin “D” connector:RS-232RJ-45 jack (cardfile topmounted)22.25 lbs. (10 kg), *typicalwith all PCBs installed.-40°C to +70°C (-40°F to+158°F)95%, non-condensing, p. 7
Page 1 and 2: Wayside SignalingSystemsAnsaldo STS
Page 3 and 4: Cardfiles (MicroLok II Applications
Page 5: Cardfiles (MicroLok II Applications
Page 9 and 10: Cardfiles (MicroLok II Applications

RSE-1D1 - Ansaldo STS

Create successful ePaper yourself

Delete template?

Save as template?