Getting Started With Pro/ENGINEER Wildfire 2.0 - STROJNISTVO.com

More documents

Recommendations

Info

Scaling Drawings and Views 6-5 Using Formats and Templates 6-6 Creating a New Drawing File 6-7 Modify the View 6-7 Add a Detailed View 6-8 Show Dimensions 6-9 Insert Added Dimensions 6-11 Clean Up the Dimensions 6-12 Edit Witness Lines and Arrows 6-12 Finishing Sheet One 6-14 Create an Exploded Assembly View 6-14 Creating a Bill of Materials 6-16 Create the Table 6-16 Enter Text Headings 6-17 Define a Repeat Region 6-17 Add BOM Parameters 6-18 Show BOM Balloons 6-18 Chapter 7 Getting Productive Using Layers and the Layer Tree 7-1 Using Family Tables 7-2 Managing the Pro/ENGINEER Environment 7-3 Using Configuration Files 7-3 Understanding the Startup Search Sequence 7-4 Loading a Configuration File 7-5 Setting Configuration Options 7-5 Understanding When Options Take Effect 7-6 Editing Configuration Options and Values 7-6 Navigating the Configuration Options 7-7 Using Keywords and Wildcards in Searches 7-7 Using Mapkeys to Simplify Command Sequences 7-7 Defining a Mapkey 7-7 Placing Icons on Toolbars 7-9 Improving System Performance 7-9 xii Getting Started With Pro/ENGINEER Wildfire 2.0
Chapter 8 Getting Support Help Center: Help and Books 8-1 Pro/ENGINEER Resource Center 8-2 PTC Technical Support 8-2 PTC Training Services 8-2 Pro/ENGINEER User Community 8-3 Glossary Glossary-1 Index Index-1 Contents xiii
Page 1 and 2: Parametric Technology Corporation G
Page 3 and 4: outside of the United States. Conta
Page 5: License Version 1.1 (at http://www.
Page 8 and 9: Deleting Files 2-6 The Viewing Cont
Page 10 and 11: Apply Rounds to the Pattern 4-45 Ex
Page 15 and 16: Intended Audience About This Guide
Page 17: Additional Documentation The follow
Page 20 and 21: Existing designs can be adapted to
Page 22 and 23: Assembly Mode Drawing Mode After th
Page 25 and 26: 2 Learning the User Interface This
Page 27 and 28: File Management The Working Directo
Page 29 and 30: Creating Files Use File > New to st
Page 31 and 32: The Spin Center Use the default par
Page 33 and 34: The Hole dashboard placement panel
Page 35 and 36: Selection . filters Selection Lists
Page 37 and 38: 3 Part Design Basics In the previou
Page 39 and 40: The more you can foresee areas of p
Page 41 and 42: Finalizing dimensions in Sketcher M
Page 43 and 44: Left: Extruded protrusion. Right: R
Page 45 and 46: Rectangle . section and dimensions
Page 47 and 48: 4 Modeling the Cell Phone Now that
Page 49 and 50: 2 Click the Front datum plane (FRON
Page 51 and 52: Sketching . plane with centerlines
Page 53 and 54: Mirror Geometry of a Section Now cr
Page 55 and 56: 2 Enter a depth of 0.05 for the ext
Page 57 and 58: Summary You have created and saved
Page 59 and 60: 3D circle with strong dimensions Gu
Page 61 and 62: The referenced radial hole Create t
Page 63 and 64:
Part 3: Microphone The microphone p
Page 65 and 66:
3D . extrusion 1 Click Insert > Ext
Page 67 and 68:
. Verify the inward direction of th
Page 69 and 70:
2 Add all the outer edges of the pr
Page 71 and 72:
Sketch the Slot Section Create the
Page 73 and 74:
Summary 7 Click the check icon to f
Page 75 and 76:
Dimensions for the PC board sketch
Page 77 and 78:
distance values, or double-click a
Page 79 and 80:
Summary 2 Click the front surface o
Page 81 and 82:
Rough sketch of the antenna tip Pro
Page 83 and 84:
Add the Revolved Cut can be set (up
Page 85 and 86:
parallel to the bottom of the cut s
Page 87 and 88:
Part 6: Keypad The earpiece exercis
Page 89 and 90:
Round the Corners Create the First
Page 91 and 92:
The finished pattern Apply Rounds t
Page 93 and 94:
Sketch the Large Button Section Ske
Page 95 and 96:
Dimension IDs 1 To enter a relation
Page 97 and 98:
Part 7: Back Cover The construction
Page 99 and 100:
Create the First Cut An angled slic
Page 101 and 102:
Round the Corners and the Cut Edge
Page 103 and 104:
The draft handles The completed dra
Page 105 and 106:
Create the Antenna Brace The antenn
Page 107 and 108:
5 Round the joint between the brace
Page 109 and 110:
Dimensions for the post feature Mod
Page 111 and 112:
Countersunk hole setup values Copy
Page 113 and 114:
Summary 5 In the graphics window or
Page 115 and 116:
Technique or Feature Where Introduc
Page 117 and 118:
The new datum is added, offset into
Page 119 and 120:
Setting up the lens housing sketch
Page 121 and 122:
Dimensions for the earpiece cut sec
Page 123 and 124:
Face edge rounds Shell the Solid Ap
Page 125 and 126:
The lens cut sketching plane and th
Page 127 and 128:
Cut Out the Lens An existing edge m
Page 129 and 130:
Setting up the earpiece cuts 2 Plac
Page 131 and 132:
Creating the earpiece holder A simi
Page 133 and 134:
Add the Microphone Cut and Holder T
Page 135 and 136:
Create the Screw Posts and Holes Th
Page 137:
Summary Post features ready to mirr
Page 140 and 141:
Automatic Placement Many automatic
Page 142 and 143:
Lens Part automatically. The orient
Page 144 and 145:
Microphone Part First earpiece refe
Page 146 and 147:
PC Board Part Microphone fully cons
Page 148 and 149:
Keypad Part Third PC board referenc
Page 150 and 151:
Partially constrained keypad 3 For
Page 152 and 153:
Back Cover Part modified in the ass
Page 154 and 155:
Antenna Part Assembly and part Sear
Page 156 and 157:
The . Explode Position dialog box N
Page 158 and 159:
2 Enter 2.0 for the Mate offset val
Page 161 and 162:
6 Creating Drawings A mechanical dr
Page 163 and 164:
Drawing view of 3D model with no di
Page 165 and 166:
Creating Detailed Views Alignment.
Page 167 and 168:
Creating a New Drawing File Modify
Page 169 and 170:
Show Dimensions Sketching 1 an outl
Page 171 and 172:
Tip detailed . view after showing d
Page 173 and 174:
Tip . view solution Finished sheet
Page 175 and 176:
General view of the exploded assemb
Page 177 and 178:
4 Two rows are needed to start, one
Page 179:
Exploded view with BOM balloons Cre
Page 182 and 183:
View and change layer display statu
Page 184 and 185:
In the config.pro file, each option
Page 186 and 187:
When Current Session is displayed i
Page 188 and 189:
2 Click New in the Mapkeys dialog b
Page 191 and 192:
8 Getting Support This chapter prov
Page 193:
Pro/ENGINEER User Community Pro/USE
Page 196 and 197:
detailed view A drafting view that
Page 199 and 200:
Index Index-1
show all

Getting Started With Pro/ENGINEER Wildfire 2.0 - STROJNISTVO.com

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?