HERE - Densen

More documents

Recommendations

Info

15DM-10Integrated amplifierm n oal b c d e f h g h a j klistening to, that is also sent to the Tape deck forrecording, so do not switch input during recording.Tape monitoring is not possible. If you need to beable to monitor your recording, use a headphoneconnected to your tape deck. This output is notbuffered, so switch off your tape deck, when it is notin use.g: Tape input 2.h: Tape output 2 (connects to line in on your Tapedeck, for recording). It is always the channel you arelistening to, that is also sent to the Tape deck forrecording, so do not switch input during recording.Tape monitoring is not possible. If you need to beable to monitor your recording, use a headphoneconnected to your tape deck. This output is notbuffered, so switch of your tape deck, when it is not inuse.j: Main input. Only power the amplifier with themains voltage indicated on the sticker on the backpanel. The mains input also contains a socket forfuses, which must only be replaced with same type offuse as indicated on the sticker on the back panel.k: Power on/off switch.l: Ground screw for grounding of turntables.m: Volume control. Must be set to zero when the ampis not in use.n: Red light, which indicates when the amp is on.o: Selector switch. When turned fully to the left, input
16DP-Drive/01/02MM/MC RIAA stageA response to numerous suggestions to make a separate RIAA-Stage, the DP-Drive contains a separate power supply, a precisepower regulator and a docking-station for the DP-01MM and DP-02MC boards. Each of these contains acomplete RIAA stage and,despite their modestprice, offers the best of<strong>Densen</strong> design. The DP-01MM stage is designed towork perfectly with virtually allMM cartridges on the market, due to thespecial design of the circuit.In the DP-02MC stage, we went a step further and designed thecircuit both to be immune to various cartridge loads and, with aspecial light-driven power supply, to have the world’s lowestnoise-floor for an MC-stage. The DP-01MM can be used with the B-100/B-200/DM-10/DM-20/DM-30 and DP-Drive. The DP-02MCcan only be used with theDP-Drive.Back panel connections:a: Ground connector.b: Phono in: The turntable is connected to this input.c: Pre out: This is connected to a line input of thepreamp or integrated amplifier with which the DP-Drive is used.d: The DP-Drive comes complete with an externalpowersupply. This powersupply is connected to thisinput.e: Power: On/Off: switch. Please put the switch to off,when the DP-Drive is equipped with a DP-02, and theDP-Drive is not in use.Front:f: Powerindicator: light is red when the power is on.Internally the DP-Drive can be fitted with either a DP-01 MM stage or a DP-02 MC stage.
Page 2 and 3: ContentsReceiving your new Densen p
Page 4 and 5: 5ConnectionsAlways connect and disc
Page 6 and 7: 7BEAT B-100Integrated amplifierm n
Page 8 and 9: 9BEAT B-200Pre amplifierts u y y v
Page 10 and 11: 11BEAT B-300 (XS)Power amplifierfb
Page 12 and 13: 13BEAT B-400 (XS)CD playerj k l m r
Page 16 and 17: 17DP-Drive/01/02MM/MC RIAA stagefa
Page 18 and 19: 19Speaker cables:Make sure that you
Page 20 and 21: 21Non-Feedback technologyThe most i
Page 22: 23BEAT B-400CD playerDP-01MM phonos

HERE - Densen

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?