HERE - Densen

More documents

Recommendations

Info

5ConnectionsAlways connect and disconnect cables, when your Densen isswitched off, and the power is removed. Otherwise you will riskdamages not covered by the warranty.Statement of conformityThe Densen products comply with IEC65 & EN61000-3-2.Incidently, the various wiring possibilities for the variousproducts are indicated in the product descriptions that will followlater in this owner’s manual.DP-01 PhonostageMany of the Densen amplifiers have sockets for the DP-01 Riaa.This is connected by removing the lid and mounting it preciselyin the socket dedicated to DP-01. Before mounting, two jumpersplaced on the DP-01 socket, should be removed. In the productdescriptions you can read precisely how it should be positionedin each separate unit.VERY IMPORTANTMounting of DP-01 should only be carried out by your dealer.
6BEAT B-100Integrated amplifierBased on the DM-10, the BEAT-100 was designed to bring you thebest qualities of the DM-10 at a much lower price. The BEAT-100is a true non-feedback amplifier, and contains designer goodieslike Alps potentiometer, massivetoroidal transformer, custommadecapacitors,doublesided teflon PCBand goldplated in- andoutput terminals. Thecircuit is optimized for SMD(surface mounted devices), and thetransistors, capacitors and resistors are all measured beforemounting, to obtain the highest precision.The reviews has confirmed the quality of the BEAT-100 byawarding the BEAT-100 with a string of very favorable reviews:”You just can’t beat it”, ”rhythmic magic” and ”build quality thatshould embarrass everyone fighting inthis price category” and “itdoes so much right thateven really expensiveamps get wrong, that itmight even start youthinking!”.It all tells you it is time to open your earsand listen.Back panel connections:a: Speaker terminals. The amplifier is prepared forone pair of speakers, but has 2 separate outputs perchannel, to allow bi-wiring (separate speakers cablesfor bass and midrange/treble). Red must beconnected to red/+ on your speakers, and black toblack/- on your speakers. Left channel must beconnected to left side speakers, and right channel toright side speakers. Do not short circuit!b: Input 1. Is a line input that can be converted bymounting a DP-01 MM board internally to aturntable input.To connect the DP-01 correctly, lift of the top cover,and remove the two black jumpers from the DP-01socket on the left of the mains board, when seen fromthe back panel. Mount the DP-01 so that all the largecomponents on the DP-01 are facing down towardsthe bottom of the B-100. Mount the DP-01 so that all12 pins on the socket on the board are mounted inthe holes on the socket of the DP-01.c: Line input 2d: Line input 3e: Line input 4f: Line input 5g: Tape inputh: Tape output (connects to line in on your tape deck,for recording). It is always the channel you arelistening to that is sent to the tape deck for recording,
Page 2 and 3: ContentsReceiving your new Densen p
Page 6 and 7: 7BEAT B-100Integrated amplifierm n
Page 8 and 9: 9BEAT B-200Pre amplifierts u y y v
Page 10 and 11: 11BEAT B-300 (XS)Power amplifierfb
Page 12 and 13: 13BEAT B-400 (XS)CD playerj k l m r
Page 14 and 15: 15DM-10Integrated amplifierm n oal
Page 16 and 17: 17DP-Drive/01/02MM/MC RIAA stagefa
Page 18 and 19: 19Speaker cables:Make sure that you
Page 20 and 21: 21Non-Feedback technologyThe most i
Page 22: 23BEAT B-400CD playerDP-01MM phonos

HERE - Densen

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?