MAGIC BOND EPOXY STICK- GREEN, WHITE, ALUM., COPPER ...

ITW DevconPart No.: 11600MAGIC BOND EPOXY STICK- GREEN, WHITE, ALUM., COPPER, BLUEThis product appears in the following stock number(s):11600 11600G 11605 11610 11615 11620 DA004 DE143DE154 DE158 DE166 DE220 DE230 DE600 DE600B DE603Last revised: 08/13/021. CHEMICAL PRODUCT AND COMPANY IDENTIFICATIONTradename: MAGIC BOND EPOXY STICK- GREEN, WHITE, ALUM., COPPER, BLUEGeneral use:Chemical family:When fully cured, the mixed product is non-hazardous.Epoxy Resin & Polymercaptan Curing Agent.Material Safety Data SheetPage 1Printed: 1/28/2004MANUFACTURERITW Devcon30 Endicott St.Danvers, MA 01923EMERGENCY INFORMATIONEmergency telephone number(CHEMTREC): (800) 424-9300Other Calls: (978) 777-11002. COMPOSITION/INFORMATION ON INGREDIENTSHAZARDOUS CONSTITUENTSConstituentAbbr.CAS No.WeightpercentACGIHTLVExposure limitsOSHAPELOtherLimitsAluminum oxide 1344281 < 5 10 mg/m3 (E) 15 mg/m3 10 mg/m3(Canada)Aminoethylpiperazine AEP 140318 1-10 n/en/e n/eCrystalline silica 14808607 < 1 0.05 mg/m3 10/(%Q+2) mg/m3 0.10 mg/m^3(Canada)Bisphenol A diglycidyl ether resin DGEBPA 25068386 5-20 n/en/e n/eGlass Oxide 65997173 15-30 n/en/ePolymercaptan curing agent * 5-15 n/en/en/en/e"TLV" means the Threshold Limit Value exposure (eight-hour, time-weighted average, unless otherwise noted) established by the AmericanConference of Governmental Industrial Hygienists. "STEL" indicates a short-term exposure limit. "PEL" indicates the OSHA Permissible ExposureLimit."n/e" indicates that no exposure limit has been established. An asterisk (*) indicates a substance whose identity is a trade secret of our supplierand unknown to us.3. HAZARDS IDENTIFICATIONEmergency OverviewAppearance, form, odor: putty with low odor.WARNING! Eye and skin irritant. Potential skin sensitizer. May be harmful if swallowed.MSDS0619

ITW DevconPart No.: 11600Potential health effectsSkin: May cause irritation to sensitive skin.Eyes: Mild irritation.Inhalation:No data.Primary routes of exposure:Symptoms of acute overexposure:Ingestion:No data. May cause irritation, nausea, vomiting, diarrhea.Effects of chronic overexposure:Prolonged or repeated overexposure may cause allergic senitization (rash, itching, redness). A component in producthas shown activity by in vitro microbial mutagenicity screening and produced chromosomal abberations in cultured ratliver cells.Carcinogenicity -- OSHA regulated: No ACGIH: No National Toxicology Program: YesMedical conditions which may be aggravated by exposure:Allergies, skin disorders.4. FIRST AID MEASURESFirst aid for eyes:Flush with clear water for 15 minutes.First aid for skin:Remove contaminant and contaminated clothing. Wash thoroughly with soap and water.First aid for inhalation:Remove to fresh air.First aid for ingestion:Contact a physician. Do NOT induce vomiting.5. FIRE FIGHTING MEASURESExtinguishing media:WaterFlash Point (°F): >500International Agency for Research on Cancer: YesCancer-suspect constituent(s) : respirable crystalline silicaCarbon dioxide Dry chemical Foam Alcohol foamMethod: TCCExplosive limits in air (percent) -- Lower: n/dSkin contact Skin absorption Eye contact Inhalation IngestionUpper: n/dSpecial firefighting procedures:Firefighters should wear self-contained breathing apparatus and protective clothing.Unusual fire and explosion hazards:Toxic smoke and vapors may form during decomposition.Material Safety Data SheetHazardous products of combustion:Oxides of carbon, sulfur and nitrogen. Aldehydes, ketones and other unknown organic compounds.Page 2MSDS0619

ITW DevconPart No.: 116006. ACCIDENTAL RELEASE MEASURESMaterial Safety Data SheetPage 3Spill control:Not applicable.Containment:Not applicable.Cleanup:Absorb spillage on inert material and discard in suitable containers.Special procedures:Prevent spill from entering drainage/sewer systems, waterways, and surface waters.7. HANDLING AND STORAGEHandling precautions:---Keep hands away from eyes when handling material or before washing after use. Wash thoroughly after using--particularly before eating or smoking.---If this product is sanded or machined after curing, take appropriate precautions against inhalation of nuisanceparticulates. A TLV of 2 mg/m3 should be observed.Storage:---Store in a cool, dry place.8. EXPOSURE CONTROLS/PERSONAL PROTECTIONEngineering controlsVentilation :General mechanical is satisfactory. If odor is disagreeable, use local exhuast.Other engineering controls :Have emergency shower and eye wash available.Personal protective equipmentEye and face protection:Safety glassesSkin protection:Polyethylene gloves for prolonged use.Respiratory protection:None needed in normal use with proper ventilation.MSDS0619

ITW DevconPart No.: 11600Material Safety Data SheetPage 49. PHYSICAL AND CHEMICAL PROPERTIESSpecific gravity: 1.9Melting point (°F): n/dVapor pressure (mmHg): Nil at 78 °FVOC (grams/liter): 0Percent volatile by volume: 0Percent solids by weight: 100Boiling point (°F):n/dVapor density (air = 1): >1Evaporation rate (butyl acetate = 1):

ITW DevconPart No.: 11600Material Safety Data Sheetactivity. 3) The International Agency for Research on Cancer (IARC) concluded that DGEBPA is not classifiable as acarcinogen (IARC group 3), that is human and animal evidence of carcinogenicy is inadequate.Other chronic effects:Prolonged or repeated skin contact may cause sensitization, with itching, swelling, or rashes on later exposure.Studies have shown bisphenol A diglycidyl ether resin to cause allergic contact dermititis.Page 5Toxicological information on hazardous chemical constituents of this product:ConstituentOral LD50(rat)Dermal LD50(rabbit)Inhalation LC504hr, (rat)Aluminum oxide n/d n/d n/dAminoethylpiperazine 2140 mg/kg 880 mg/kg n/dCrystalline silica n/d n/d n/dBisphenol A diglycidyl ether resin 11.4 g/kg >20 ml/kg no deathsGlass Oxide n/d n/d n/dPolymercaptan curing agent n/d n/d n/d12 ECOLOGICAL INFORMATIONEcotoxicity:Not available.Mobility and persistence:Not available.Environmental fate:Not available.'n/d' = 'not determined'13. DISPOSAL CONSIDERATIONSPlease see also Section 15, Regulatory Information.Waste management recommendations:Remove to a waste disposal facility operating in compliance with state and local regulations.MSDS0619

ITW DevconPart No.: 1160014. TRANSPORT INFORMATIONMaterial Safety Data SheetPage 6Proper shipping name: NRTechnical name : N/AHazard class :N/AUN number:N/APacking group:N/AEmergency Response Guide no.:IMDG page number: N/AOther:N/AN/AORM-D : N/ALtdQty : N/A15. REGULATORY INFORMATIONU.S. Federal RegulationsTSCAAll : ingredients of this product are listed, or are exempt from listing, on the TSCA inventory.The following RCRA code(s) applies to this material if it becomes waste:NoneRegulatory status of hazardous chemical constituents of this product:ConstituentExtremelyHazardous*ToxicChemical**CERCLARQ (lbs)TSCA 12B ExportNotificationAluminum oxide No Yes 0.0 Not requiredAminoethylpiperazine No No 0.0 Not requiredCrystalline silica No No 0.0 Not requiredBisphenol A diglycidyl ether resin No No 0.0 Not requiredGlass Oxide No No 0.0 Not requiredPolymercaptan curing agent No No 0.0 Not required*Consult the appropriate regulations for emergency planning and release reporting requirements for substances on the SARA Section 301Extremely Hazardous Substance list.**Substances for which the "Toxic Chemical" column is marked "Yes" are on the SARA Section 313 list ofToxic Chemicals, for which release reporting may be required. For specific requirements, consult the appropriate regulations.For purposes of SARA Section 312 hazardous materials inventory reporting, the following hazardclasses apply to this material: - Immediate health hazard -- Delayed health hazard -Canadian regulationsMSDS0619

ITW DevconPart No.: 11600Material Safety Data SheetPage 7WHMIS hazard class(es) : D2B; D2AAll components of this product are on the Domestic Substances List.16. OTHER INFORMATIONHazardous MaterialsIdentification System (HMIS)ratings:Health1*Flammability1Reactivity0The information and recommendations in this document are based on the best information available to us at the time of preparation, but we make noother warranty, express or implied, as to its correctness or completeness, or as to the results of reliance on this document.MSDS0619