SV-Series Operation Manual - BJM Pumps

More documents

Recommendations

Info

Do not run the pump dry.Pump liquid should not exceed a maximum temperature of 104°F.Never place the pump on loose or soft ground. The pump may sink, preventingwater from reaching the impeller. Place on a solid surface or suspend the pumpwith a lifting rope/chain. The SV Series pumps are provided with a suctionstrainer to prevent large solids from clogging the impeller. Any spherical solidswhich pass through the strainer should pass through the pump.For maximum pumping capacity, use the proper size non-collapsible hose or rigidpiping. A check valve may be installed after the discharge to prevent back flowwhen the pump is shut off.PUMP ROTATIONTwo ways to check the correct pump rotation:1. By looking at the impeller; the rotation of the impeller should be counterclockwise as shown in the picture below.2. By looking from the top of the pump. Since the impeller cannot be seen, the bestway to check the rotation is to check the kick back motion of the pump when thepump just starts. The kick back motion of the pump should be counter clockwiseas shown in the picture below.8
PUMP OPERATIONThis pump is designed to handle dirty water that contains somesolids. It is not designed to pump volatile or flammable liquids. Do not attempt to pumpany liquids which may damage the pump or endanger personnel as a result of pumpfailure.Do not operate this pump where explosive vapors orflammable material exist. Death or Serious injury will result.TYPICAL MANUAL DEWATERING INSTALLATIONNOTE: Maximum recommended starts should not exceed 10 times per hour.MANUAL OPERATIONAll SV models are provided with a 33’ (10 m) power cable. NEVER splice the powercable due to safety and warranty considerations. Always keep the plug end dry.Note: 230V, single phase and 208V, 230V, 460V & 575V three phase units do nothave a plug and have to be provided separately.Do not alter the length or repair any power cable with a splice. Thepump motor and cable must be completely waterproof. Damage to the pump orpersonal injury may result from alterations.For manual operation: 115 volt: plug the power cable into any 115 volt groundedreceptacle. 208, 230, 460 & 575 volt: Attach the proper plug, connect directly to thepower source or control box. Check the direction of the rotation. Tilt the pump and startit. It should twist in the opposite direction of the arrow (on pump). It is recommendedthat a Ground Fault Interrupter (GFI) type receptacle (or equivalent) be used.9
Page 1: INSTALLATION, OPERATION & MAINTENAN
Page 4 and 5: INTRODUCTIONThis Installation, Oper
Page 6 and 7: INSPECTIONReview all safety informa
Page 10 and 11: Single phase pumps always use a thr
Page 12 and 13: STOPPINGTo stop the pump (manual an
Page 14 and 15: Typical 3 phase Auto Control 1Befor
Page 16 and 17: Pump should be inspected at regular
Page 18 and 19: EXPLODED VIEW OF SV75018
Page 20 and 21: EXPLODED VIEW OF SV1500C20
Page 22 and 23: EXPLODED VIEW OF SV08C22
Page 24 and 25: EXPLODED VIEW OF SV22C, SV37C24
Page 26 and 27: SV SERIES PARTS LISTPump Model SV25
Page 28 and 29: SINGLE PHASE WIRING DIAGRAM 115V &
Page 30 and 31: 230VMODELS SV08, SV08C, SV15C, SV22
Page 32 and 33: 575VMODELS SV08, SV08C, SV15C, SV22
Page 35 and 36: BJM PUMPS, LLC123 Spencer Plain Roa
Page 37 and 38: START-UP REPORT FORMAre guide rails
Page 39 and 40: NOTES:

SV-Series Operation Manual - BJM Pumps

Create successful ePaper yourself

Delete template?

Save as template?