method with inserts.pdf

COMPONENT COVERAGES
Included in the coverages below is the replacement of all covered components resulting from a breakdown
or the gradual reduction in performance due to normal wear and tear, when the wear exceeds the manufactures specifications.
Engine: All internally lubricated parts of the engine, including but not limited to pistons; piston rings; wrist pins; crankshaft and main bearings;
connecting rods and rod bearings; camshaft and camshaft bearings; eccentric shaft; oil pump; push rods; rocker arms; rocker arm shafts; replaceable
guides and seats; timing chain; timing gears; hydraulic lifters; intake and exhaust valves; and valve springs. Also engine torque strut; harmonic
balancer; head gasket; timing belt; timing cover; intake and exhaust manifolds; valve covers; flexplate or flywheel (only if not damaged by a manual
clutch disc or other clutch component); oil pan; dipstick and tube; engine block; engine mounts and cushions; pulleys; cylinder heads; water pump.
Turbo/Supercharger: Turbo or supercharger housing and all internally lubricated parts (only if damaged by the failure of a part covered
under this Named Component Coverage). Note: Only original OEM equipment qualifies for coverage.
Transmission: All internally lubricated parts of manual or automatic transmissions, including but not limited to: gears; input and output
shafts; bearings; oil pump; planetaries; pressure regulator valve; stator and stator shaft; sprags; separator plate; governor assembly;
overdrive carrier; reaction carrier; center support; valve body; torque converter; parking lock actuator; dipstick and tube; vacuum modulator;
internal linkage; transmission control unit. Note: transmission case, dipstick and filler tube, torque converter housing and overdrive housing
are also covered only if damaged by the covered failure of any of the above listed parts.
Drive Axle: Drive shaft; axle shaft(s); axle bearings; universal joints; constant velocity joints; ring and pinion gears; pinion bearings; supports;
retainers; carrier assembly; side carrier bearings; thrust washers. Note: Drive axle housing is covered only if damaged by the covered
failure of any of the above listed parts.
4X4/AWD: Front drive shaft; axles; locking hubs; locking rings; differential; universal joints; constant velocity joints; main shaft; drive chain;
gears; bearings; thrust washer and shims. Note: Transfer case housing is also covered only if damaged by the covered failure of any of the
above listed parts.
Air Conditioning (Optional): Compressor; compressor clutch and pulley; condenser; evaporator; accumulator; coil; expansion
valve; blower motor; serpentine belt tensioner; power module; idler pulley and bearing; ducts and outlet hoses; orifice tube; high/low cutoff
switches; pressure cycling switch; receiver/dryer. Note: If the covered costs to repair an R-12 system exceed the cost to convert to an
R-143a system, the system will be converted to use R-143a refrigerant. Note: Refrigerant is also covered if required in connection with a
covered breakdown.
Electrical (OPTIONAL): Starter motor; alternator; voltage regulator; main battery; ignition module; ignition coil; distributor; starter
solenoid; front and rear wiper motors; wiper module; washer pump and switch; power window motors; power seat motors; power door lock
actuator; power antenna motor; power mirror motor; power trunk motor; rear spoiler motor; steering column motor; stepper motor, relays and
pump; cruise control transducer; pole pieces; condenser fan motor; DK motor; headlight motor; idle air control motor; idle speed control motor;
aspirator fan motor; phase control motor.
Seals & Gaskets (OPTIONAL): Coverage is provided for seals and gaskets provided the vehicle has less than 150,000 miles at the time of
purchase and will continue until the Vehicle reaches 250,000 miles or the expiration date shown on the Declaration Page (whichever occurs first). Note:
A seal or gasket must show an active leak or drip for coverage to apply; minor seepage is considered normal and will not be considered a breakdown.
Taxes and Fluids: State and local taxes where applicable and fluids required to complete covered repairs.
program highlights
Matrix Method’s CruiseControl product is a strong entry-level Vehicle Service Contract that offers flexible and affordable component
coverage and options. CruiseControl covers the vehicle’s powertrain and has optional coverage for the air conditioning, electrical, first
day coverage and seals and gaskets. Deductibles are offered at an affordable $250 (standard) and $100 (optional), as well as a $250
disappearing (optional). The program is available on vehicles 20 years old and newer with less than 200,000 miles at the time of sale.
A range of terms is available starting with 12 months/25,000 miles and going up to 60 months/100,000 miles from the date of sale. In
addition, an option on the 36 months/100,000 mile term allows the contract holder to extend the term 12 months (maximum of two
extensions) for a nominal charge.
When your customer’s budget is limited, or the lending source will not approve a higher priced vehicle service contract, CruiseControl fits
the bill. Your customers will feel more comfortable knowing that the major parts and components of their vehicle are covered and that they
will be protected from the high cost of an unexpected repair at a price they can afford.
A Future Guarantee is another dealership benefit to the CruiseControl program. This means being automatically enrolled in Matrix Warranty
Solutions’ no cost follow-up program for warranty holders. Our professionally trained specialists will contact your customers 60 days prior to
the expiration of their CruiseControl contract and offer them an opportunity to upgrade their coverage to either Matrix Method’s HeadStart or
GoMonthly programs.
The above is for informational purposes only, refer to the Vehicle Service Contract for complete details.