thoroughly
Hobby World Corporation gasser conversion - Centuryhelimedia.com
Hobby World Corporation gasser conversion - Centuryhelimedia.com
- No tags were found...
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
LANDING FRAME STRUCTURE<br />
T700 GASSER CONVERSION<br />
When installing the engine assembly to the frames, do not tighten one side<br />
all the way leaving the other side completely loose. Tighten the M4x20 bolts<br />
on either side of the frames evenly moving from one side to the other. Leave<br />
the engine bolts loose for now as you will need to adjust the engine position<br />
once you attach the side frames to this engine assembly.<br />
Make sure to apply medium threadlock to these bolts. After you have installed<br />
the left and right M4x20 bolts, install the front engine block making<br />
sure to use medium threadlock on the M4x20 bolt holding the engine’s head<br />
in place.<br />
CA<br />
1 2<br />
12<br />
13<br />
Install the landing skids onto the landing struts one side at a time.<br />
After installing the landing skids, position, the landing struts on the<br />
skids so that they match up with the mounting positions on the<br />
frames. Place the washers onto the M3x18 cap screws and then apply<br />
medium threadlock. Install the screws through the landing struts<br />
and tighten onto the frames. Turn the landing skids so that the curve<br />
towards the front is facing straight up. Install the four M3x4 set<br />
screws to lock the skids into place. Do not tighten these too much<br />
as you can crack the plastic struts. Lastly, install the landing skid<br />
stoppers.<br />
9<br />
4<br />
5<br />
3<br />
Hint: Leave the front strut’s set screws and the<br />
M3x18 cap screws off. This will allow you to<br />
slide the strut forward giving you access to tighten<br />
the front engine mounting block once you attach<br />
the engine assembly to the side frames.<br />
7<br />
6<br />
8<br />
10 11<br />
CNM3x7FW<br />
CNM2.5x8CS<br />
CNM4x20CS<br />
CNM4x10FW<br />
CNM3x4SS<br />
CNM3x18CS<br />
No. Part #<br />
Description Qty<br />
1<br />
2<br />
3<br />
4<br />
5<br />
6<br />
7<br />
8<br />
9<br />
10<br />
11<br />
12<br />
13<br />
HW6117G3A Front Engine Mounting Block ( 引 擎 固 定 块 ) 1<br />
CNM4x20CS M4X20 Cap Screw( 杯 头 内 六 角 螺 丝 )<br />
1<br />
HW6117G30 Landing Gear Frame( 引 擎 座 底 板 ) 1<br />
CNM3x7FW 3x7x1 Washer( 垫 片 )<br />
2<br />
CNM2.5x8CS M2.5x8 Cap Screw( 杯 头 内 六 角 螺 丝 )<br />
2<br />
HI6122D Landing Struts( 脚 架 ) 2<br />
CNM3x4SS M3x4 Set Screw( 无 头 内 六 角 螺 丝 )<br />
4<br />
HW3123B Aluminum Skids with Caps ( 脚 架 弯 管 )<br />
2<br />
CNM3x7FW 3X7X1 Washer( 垫 片 )<br />
4<br />
CNM3x18CS M3x18 Cap Screw( 杯 头 内 六 角 螺 丝 )<br />
4<br />
HW3123B Skid Caps( 脚 架 塞 )<br />
4<br />
CNM4x20CS M4X20 Cap Screw( 杯 头 内 六 角 螺 丝 )<br />
2<br />
CNM4x10FW 4X10X1 Washer( 垫 片 )<br />
4<br />
Page 11