Diamond Tools and Machines - English

More documents

Info

MACHINES 108 Core drilling system BC-2 electric Core drilling up to Ø 1 000 mm High stability yet low weight thanks to 2-pillar guide system Effortless drilling thanks to two speed feed gearbox i=1:2 and i=1:9 Bores with a diameter of up to 1 000 mm with Modul- Drill distance plates The BC-2 is ideal for drilling large holes up to 1 000 mm. Thanks to the modular design, combined use with Tyrolit cable saws and hydraulic equipment is possible without difficulty. The dual-column guidance principle and a two-speed feed gear enable user friendly work and low weight. A large selection of drill accessories rounds off the range.
MACHINES 109 System & Accessories Technical data System & Accessories Drill rig BC-2 Drill diameter range Max. drill diameter with distance plates Max. drill bit length Design Steel dowel foot Two-speed feed gearbox i=1:2 and i=1:9 Feed using hand crank Can be adjusted to any angle Adjusting feet (micro) Dimensions & Weight Length Width Height Weight 100–400 mm 1 000 mm 980 mm 460 mm 290 mm 1 340 mm 30 kg 964906 ModulDrill distance plate Ø +180 mm 964907 ModulDrill distance plate Ø +250 mm 977464 ModulDrill mounting plate 974270 Extraction device for core bits 977353 Extraction device for cores 977462 Handwheel complete 974264 Trolley chassis 975746 Tool box 10991465 Water tank 10 l System suggestion Core drilling system BC-2 974266 Drill rig BC-2 984076 Fastening plate for ModulDrill 10991100 Drill gearbox DGB1000 10998369 Drilling and circular wire saw kit WSE1621 10997955 Electric main drive motor WSE1621 400–480 V / 50 Hz 974263 Feed gear 2-speed 11002700 Electric control unit WSE1621 400 V | 50 Hz incl. radio remote control 10987583 Feed motor 11002077 Fastening bolt assembly 11002624 Drill hammer DHE32 / 230 V incl. 16 mm drill
Page 1:
Diamond tools and machines for the
Page 4 and 5:
INTRODUCTION 2 The Tyrolit Group Ty
Page 6 and 7:
INTRODUCTION 4 Leading through true
Page 8 and 9:
QUALITY LINES 6 Quality lines Tyrol
Page 10 and 11:
EXPLANATION SHORT SPECIFICATION 8 S
Page 13:
Technology from page 12 TGD ® -Tec
Page 16:
OVERVIEW OF TECHNOLOGIES 14 Convinc
Page 19:
MODULAR SYSTEM 17 Modular component
Page 23 and 24:
Diamond wet drill bits
Page 25 and 26:
DIAMOND WET DRILL BITS 23 Speeds we
Page 27 and 28:
DIAMOND WET DRILL BITS 25 Applicati
Page 29 and 30:
DIAMOND WET DRILL BITS 27 Type no.
Page 31 and 32:
DIAMOND WET DRILL BITS 29 CDL-C2 We
Page 33 and 34:
DIAMOND WET DRILL BITS 31 CDXH Wet
Page 35 and 36:
DIAMOND WET DRILL BITS 33 CD840 Wet
Page 37 and 38:
DIAMOND WET DRILL BITS 35 Type no.
Page 39:
DIAMOND WET DRILL BITS 37 B1 Wet dr
Page 42 and 43:
DIAMOND WET DRILL BITS 40 Accessori
Page 44 and 45:
DIAMOND DRY DRILL BITS 42 Drill bit
Page 46 and 47:
DRY DRILLING SYSTEM 44 Dry drilling
Page 48 and 49:
DIAMOND DRY DRILL BITS 46 DDL-RM Dr
Page 50 and 51:
DIAMOND DRY DRILL BITS 48 Type no.
Page 52 and 53:
DIAMOND DRY DRILL BITS 50 DDL Dry d
Page 54 and 55:
DIAMOND DRY DRILL BITS 52 Compact u
Page 56 and 57:
DIAMOND DRY DRILL BITS 54 Centring
Page 58 and 59:
TILE DRILLING 56 DDT Tile drills fo
Page 60 and 61: TILE DRILLING 58 Tile drill sets DD
Page 63 and 64: Machines
Page 65 and 66: SELECTING GUIDE FOR CORE DRILL SYST
Page 67 and 68: SELECTING GUIDE FOR CORE DRILL SYST
Page 69 and 70: MACHINES 67 System & Accessories Te
Page 83 and 84: RR Radio Remote RR Radio Remote RRR
Page 85 and 86: 0 1 2 h 0000000 0 BW 40 0 1 2 h 000
Page 103 and 104: MACHINES 101 System & Accessories T
Page 109: MACHINES 107 System & Accessories T
Page 113: MACHINES 111 System & Accessories G
Page 116 and 117: WALL SAWING 114 Wall saw blades Dec
Page 118 and 119: WALL SAWING 116 Selection Quality t
Page 120 and 121: WALL SAWING 118 WSL Wall saw blades
Page 122 and 123: WALL SAWING 120 SILENT Wall saw bla
Page 124 and 125: WALL SAWING 122 WSL-FAST CUT-LONG L
Page 126 and 127: WALL SAWING 124 WSL-DEEP CUT Wall s
Page 128: WALL SAWING 126 WSL Wall saw blades
Page 131 and 132: COMPATIBILITY OVERVIEW WALL SAWS 12
Page 143: MACHINES 141 System & Accessories T
Page 146 and 147: WIRE SAWING 144 Diamond wire Decade
Page 148 and 149: WIRE SAWING 146 DWM-CF Diamond wire
Page 150 and 151: WIRE SAWING 148 DWM-C Diamond wire
Page 152 and 153: WIRE SAWING 150 Diamond wire access
Page 154 and 155: COMPATIBILITY OVERVIEW WIRE SAWS 15
Page 156 and 157: MACHINES 154 Wire saw WCU17 Gross w
Page 158 and 159: MACHINES 156 Wire saw WCE18 Gross w
Page 160 and 161:
MACHINES 158 Wire saw WCE30 Gross w
Page 162 and 163:
MACHINES 160 Wire saw SB ATEX | SB-
Page 164 and 165:
MACHINES 162 Circular wire saw CCH2
Page 167 and 168:
Floor sawing Information 166 Floor
Page 169 and 170:
FLOOR SAW BLADES 167 Application re
Page 171 and 172:
FLOOR SAW BLADES FOR CURED CONCRETE
Page 173 and 174:
FLOOR SAW BLADES FOR CURED CONCRETE
Page 175 and 176:
FLOOR SAW BLADES FOR ASPHALT 173 FS
Page 177 and 178:
FLOOR SAW BLADES FOR ASPHALT 175 FS
Page 179 and 180:
FLOOR SAW BLADES FOR GREEN CONCRETE
Page 182 and 183:
MACHINES 180 Floor saw FSG513 Cutti
Page 184 and 185:
MACHINES 182 Floor saw FSG620 Cutti
Page 186 and 187:
MACHINES 184 Floor saw FSE808 Cutti
Page 188 and 189:
MACHINES 186 Floor saw FSE1022 Cutt
Page 190 and 191:
MACHINES 188 Floor saw FSE1240 Cutt
Page 192 and 193:
MACHINES 190 Floor saw FSD1274E5 3-
Page 195 and 196:
Drives Machines 194
Page 197 and 198:
MACHINES 195 System & Accessories T
Page 199 and 200:
Page 201:
Page 205 and 206:
Dry cutting
Page 207 and 208:
DRY CUTTING 205 Materials Material
Page 209 and 210:
DRY CUTTING 207 Shape Type number D
Page 211 and 212:
DRY CUTTING 209 DCU dry cutting saw
Page 213 and 214:
DRY CUTTING 211 DCU-FAST CUT dry cu
Page 215 and 216:
DRY CUTTING 213 DCC-FAST CUT wall c
Page 217 and 218:
DRY CUTTING 215 DCA+C dry cutting s
Page 219 and 220:
DRY CUTTING 217 DCH dry cutting saw
Page 221 and 222:
DRY CUTTING 219 DCM dry cutting saw
Page 223 and 224:
DRY CUTTING 221 Sharpening plate fo
Page 225:
DRY CUTTING 223 DC-CVB dry cutting
Page 228 and 229:
DIAMOND CUP WHEELS 226 Diamond cup
Page 230 and 231:
DIAMOND CUP WHEELS 228 DGU Diamond
Page 232 and 233:
MACHINES 230 Angle grinder AGE125 B
Page 234 and 235:
MACHINES 232 Angle grinder AGE230 B
Page 236 and 237:
MACHINES 234 Wall chaser HCE150 Max
Page 238 and 239:
MACHINES 236 Handheld concrete grin
Page 241 and 242:
Hand- and ring sawing
Page 243 and 244:
HAND- AND RING SAW BLADES 241 Appli
Page 245 and 246:
HAND- AND RING SAW BLADES 243 RSL R
Page 247 and 248:
HAND- AND RING SAW BLADES 245 RSM /
Page 249 and 250:
Page 251:
Page 254 and 255:
TABLE SAWING 252 Diamond saw blades
Page 256 and 257:
TABLE SAWING 254 TSU Table saw blad
Page 258 and 259:
TABLE SAWING 256 F40 Table saw blad
Page 260 and 261:
MACHINES 258 Tile saw TTE250 Cuttin
Page 262 and 263:
MACHINES 260 Tile saw TRE250 Cuttin
Page 264 and 265:
MACHINES 262 Masonry saw CSE350D Cu
Page 266 and 267:
MACHINES 264 Masonry saw TBE400 Cut
Page 268 and 269:
MACHINES 266 Masonry saw TME700 Cut
Page 270 and 271:
MACHINES 268 Masonry saw TME1000 Cu
Page 272 and 273:
MACHINES 270 Cellular concrete band
Page 275 and 276:
Further applications Filter presses
Page 277 and 278:
Page 279 and 280:
Page 281 and 282:
Page 283 and 284:
MACHINES 281 Drive BW-2 Working pre
Page 285 and 286:
MOVESMART 283 MoveSmart modules In
Page 287:
FLOOR GRINDING AND SURFACE PREPARAT
Page 290 and 291:
TYROLIT PROJECT SERVICES 288 Tyroli
Page 293 and 294:
Notes Safety 292 POS 298 General 29
Page 295 and 296:
SAFETY 293 Application Avoid uninte
Page 298 and 299:
SAFETY 296 Trouble-shooting Diamond
Page 300 and 301:
Premium grinding tools since 1919 w
Page 302 and 303:
GENERAL 300
Page 304 and 305:
GENERAL 302
Page 306:
GENERAL 304 Catalogue General infor
show all

Diamond Tools and Machines - English

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?