UPDATED

Recommendations

Info

. Click Insert Component. Notice the Insert Component dialog box. Choosing a DWG file to insert as a component of an assembly c. Navigate to the Samples folder to access mechanical drawings provided with BricsCAD: C:\Program Files\Bricsys\BricsCAD V17\en_US\Samples\Mechanical\piston d. Select the piston.dwg file and then click Open. e. Place the piston at any convenient spot in the drawing; the exact location is immaterial. Piston placed as a component in the assembly drawing 5. Repeat Insert Component to place pin.dwg as the other component. Insert it next to the piston. Pin added to the assembly drawing 208 BricsCAD V17 for AutoCAD Users
6. With the two parts in the drawing, you can attach them to each other. This is done by employing 3D constraints. Working in 3D takes pre-planning, and so let’s think through what is needed: ÐÐ ÐÐ You want the pin to stay inside the piston head The pin must be free to rotate, but it cannot slide in and out of the piston To accomplish this goal, you need to apply two 3D constraints: Concentric constraint keeps the pin centered inside the hole of the piston (but allows the pin to slide out of the piston) Tangent constraint keeps the pin from leaving the piston a. Open the 3D Constraints toolbar by right-clicking any toolbar and then choosing BRICSCAD | 3D Constraints. 3D Constraints toolbar for attaching components b. Click Concentric: : dmconcentric3d c. And then pick a curved face (a.k.a. subentities) from the piston and the pin: Select a pair of subentities: (Pick the curved face of the pin, highlighted in blue on the yellow part shown in the figure below) Entities/subentities in set: 1 Select a pair of subentities: (Pick the curved inside face of the piston, also highlighted in but on the pink part) Selecting curved surface to make components concentric TIP Should you have difficulty picking the correct face with the cursor, press the Tab key to cycle through all possible surfaces under the cursor. The command ends automatically after you pick the second subentity. Notice that the pin jumps over to the opening of the piston. The pin is inside the piston; now you use the Tangent constraint to keep the pin from sliding out of the piston. Concentric constraint lines pin up with piston’s opening 6 Working in 3D 209
Page 1 and 2:
UPDATED FOR V17 BRICSCAD ® FOR AUT
Page 3 and 4:
Table of Contents AutoCAD-BricsCAD
Page 5 and 6:
Tips Widget (BricsCAD Only)........
Page 7 and 8:
Customizing Workspaces and Quad....
Page 9 and 10:
WORKSPACES, 3D VIEWING, QUAD CURSOR
Page 11 and 12:
APPENDICES A. Command Name Cross-re
Page 13 and 14:
CHAPTER ONE BricsCAD for AutoCAD Us
Page 15 and 16:
Subscriptions. Autodesk made annual
Page 17 and 18:
ÐÐ ÐÐ ÐÐ ÐÐ ÐÐ ÐÐ Uploa
Page 19 and 20:
The BricsCAD Advantage BricsCAD sho
Page 21 and 22:
and orders them in hierarchical str
Page 23 and 24:
DS Tools from Design Sense adds to
Page 25 and 26:
Keep Your BricsCAD If you like your
Page 27 and 28:
WHAT’S MISSING FROM BRICSCAD? Bri
Page 29 and 30:
Supported Operating Systems Bricsys
Page 31 and 32:
ÐÐ ÐÐ Release notes Online tuto
Page 33 and 34:
The white layer icon indicates laye
Page 35 and 36:
Settings command extends search opt
Page 37 and 38:
dimStyle command now offers an Edit
Page 39 and 40:
mAutoUpdate variable controls wheth
Page 41 and 42:
dmTwist command modifies 3D solids,
Page 43 and 44:
3dCompareMode variable determines i
Page 45 and 46:
View properties can be edited befor
Page 47 and 48:
WHAT’S NEW IN THE BIM MODULE BIM
Page 49 and 50:
smForm command converts a selected
Page 51 and 52:
WHAT’S NEW IN FILES AppLoad comma
Page 53 and 54:
CHAPTER TWO Comparing User Interfac
Page 55 and 56:
2 Comparing User Interfaces 43
Page 57 and 58:
Start Screens BricsCAD and AutoCAD
Page 59 and 60:
‘:’ VS ‘TYPE A COMMAND’ For
Page 61 and 62:
The Prompt Menu Flags option is a b
Page 63 and 64:
Editing with the Quad With the Quad
Page 65 and 66:
TOURING THE SETTINGS DIALOG BOX Thi
Page 67 and 68:
By clicking the Find , button, you
Page 69 and 70:
ACCESSING AND MOVING BRICSCAD PANEL
Page 71 and 72:
The toolbar of the Layers panel in
Page 73 and 74:
MECHANICAL BROWSER VS PARAMETRICS M
Page 75 and 76:
Double-click a file name to open th
Page 77 and 78:
Additional status items with AutoCA
Page 79 and 80:
DIFFERENCES IN VIEW CUBES AutoCAD h
Page 81 and 82:
BricsCAD’s Select command display
Page 83 and 84:
Above: AutoCAD’s Design Center. B
Page 85 and 86:
ÐÐ Project administration for ass
Page 87 and 88:
CHAPTER THREE Compatibility of Draw
Page 89 and 90:
CHECKLIST OF DWG 2017 ENTITIES The
Page 91 and 92:
The dashes ( — ) in “read / —
Page 93 and 94:
Multilines BricsCAD reads and creat
Page 95 and 96:
HISTORY OF BRICSCAD’S DWG SUPPORT
Page 97 and 98:
Array Rectangular Associative Hatch
Page 99 and 100:
TEXT ENTITIES BricsCAD accurately d
Page 101 and 102:
DimInspect AutoCAD BricsCAD * read
Page 103 and 104:
Radius Dimensional Constraint Verti
Page 105 and 106:
Underlays AutoCAD BricsCAD * partia
Page 107 and 108:
3D Solids AutoCAD BricsCAD read / c
Page 109 and 110:
NURBS Planar Revolve Sweep 3 Compat
Page 111 and 112:
The differences in layer properties
Page 113 and 114:
Left: AutoCAD’s tabbed Modify Det
Page 115 and 116:
BricsCAD supports all the QLeader o
Page 117 and 118:
Multiline Styles BricsCAD creates m
Page 119 and 120:
Section styles are created and modi
Page 121 and 122:
Shaded shaded with Edges shades of
Page 123 and 124:
CHAPTER FOUR Customizing and Progra
Page 125 and 126:
AutoCAD Options vs BricsCAD Setting
Page 127 and 128:
The process for customizing each of
Page 129 and 130:
This reveals the items in the File
Page 131 and 132:
c. Click OK. Notice that the “Clo
Page 133 and 134:
Q: What’s the difference between
Page 135 and 136:
4. Under My Tutorial, right-click M
Page 137 and 138:
4. The toolbox created. Go ahead an
Page 139 and 140:
As with menus, the list of items in
Page 141 and 142:
Tabs. Just as a ribbon is just a li
Page 143 and 144:
CUSTOMIZING MOUSE BUTTONS & DOUBLE-
Page 145 and 146:
After downloading, load the tablet.
Page 147 and 148:
CUSTOMIZING ALIASES AND SHELL COMMA
Page 149 and 150:
Other Areas of Customization Custom
Page 151 and 152:
Both CAD systems use the same simpl
Page 153 and 154:
5. Choose the .lin file you wish to
Page 155 and 156:
.xlg .xlg Xref log files .$$$ ... E
Page 157 and 158:
.tga .tga Raster format (Targa) fil
Page 159 and 160:
BricsCAD V17 Automation Object Mode
Page 161 and 162:
ABOUT TX The TX SDK produces TX mod
Page 163 and 164:
(ADS is short for AutoCAD Developme
Page 165 and 166:
CHAPTER FIVE Operating Dual-CAD Des
Page 167 and 168:
Upgrades. Following the initial lic
Page 169 and 170: Choosing an international location
Page 171 and 172: provides other resources, such as a
Page 173 and 174: Running BricsCAD & AutoCAD in One O
Page 175 and 176: STRATEGIC IMPLEMENTATION While seve
Page 177 and 178: Tutorial: How to Add AutoCAD’s Su
Page 179 and 180: To save the current user interface
Page 181 and 182: BricsCAD’s roamable files consist
Page 183 and 184: Tutorial: Making Hidden Folders Vis
Page 185 and 186: 6. In the Customize dialog box, rig
Page 187 and 188: User Interface To fix the two probl
Page 189 and 190: My favorite feature about Linux is
Page 191 and 192: So, it can be hard — no, confusin
Page 193 and 194: CHAPTER SIX Working in 3D BRICSCAD
Page 195 and 196: BricsCAD’s Direct Modeling vs Aut
Page 197 and 198: Direct Modeling Tutorial To see how
Page 199 and 200: c. Draw a circle 65mm in diameter.
Page 201 and 202: Workspaces, 3D Viewing, Quad Cursor
Page 203 and 204: Click a triangle to change the view
Page 205 and 206: WORKING WITH THE QUAD CURSOR All ed
Page 207 and 208: WORKING WITH A 3D MOUSE BricsCAD su
Page 209 and 210: 3D Design Intent BricsCAD Platinum
Page 211 and 212: c. Click the dmExtrude button. (It
Page 213 and 214: Mechanical Browser & Hardware Libra
Page 215 and 216: To pick a part from the library, fo
Page 217 and 218: Modeling and Deforming 3D Surfaces
Page 219: Accessing Assembly Commands ÐÐ En
Page 223 and 224: With the parts are attached to one
Page 225 and 226: 6. Move the mouse to rotate the mec
Page 227 and 228: The first view placed is the front
Page 229 and 230: Section and Detail Styles You can c
Page 231 and 232: 3D Compare (new to V17) The 3dCompa
Page 233 and 234: CHAPTER SEVEN BIM, Sheet Metal, & C
Page 235 and 236: HOW BIM DESIGN WORKS BIM designs co
Page 237 and 238: 5. The next step is to tell BricsCA
Page 239 and 240: The walls look no different, and ch
Page 241 and 242: Accessing BIM Commands ÐÐ Enter o
Page 243 and 244: TUTORIAL I: HOW SHEET METAL DESIGN
Page 245 and 246: 6. Should you wish to change the an
Page 247 and 248: Adding Form Features (new to V17) F
Page 249 and 250: 1. Start BricsCAD in the Sheet Meta
Page 251 and 252: c. From the Sheet Metal ribbon’s
Page 253 and 254: 9. A few other corners need to be t
Page 255 and 256: Accessing Sheet Metal Commands ÐÐ
Page 257 and 258: Export Formats Supported Standard F
Page 259 and 260: APPENDIX A Command Name Cross-refer
Page 261 and 262: AutoCAD Command BricsCAD Command No
Page 271 and 272:
AutoCAD Command BricsCAD Command No
Page 273 and 274:
Page 275 and 276:
Page 277 and 278:
Page 279 and 280:
Page 281 and 282:
Page 283 and 284:
APPENDIX B System Variable Cross-re
Page 285 and 286:
AutoCAD AutoCAD’s BricsCAD’s Br
Page 287 and 288:
Page 289 and 290:
Page 291 and 292:
Page 293 and 294:
Page 295 and 296:
Page 297 and 298:
Page 299 and 300:
Page 301 and 302:
Page 303 and 304:
Page 305 and 306:
Page 307 and 308:
Page 309 and 310:
Page 311 and 312:
Page 313 and 314:
APPENDIX C Command Alias Cross-refe
Page 315 and 316:
AutoCAD Command AutoCAD Alias Brics
Page 317 and 318:
Page 319 and 320:
Page 321 and 322:
Page 323 and 324:
APPENDIX D Keystroke & Button Cross
Page 325 and 326:
CTRL/CMD KEYS To operate Ctrl-key s
Page 327 and 328:
SHIFT KEYS Shift keys are temporary
Page 329 and 330:
Mouse and Tablet Buttons The follow
Page 331 and 332:
The tablet overlay provided by Bric
Page 333:
3D MOUSE CONTROLS AND BUTTONS AutoC
show all

UPDATED

Create successful ePaper yourself

Delete template?

Save as template?