Souriau 8D Series - TTI Europe

More documents

Recommendations

Info

8D Series Common Section Wiring instruction Cable preparation and wire stripping Contact size L min L max #22D #20 #16 #12 #8 #4 3.58 .14 3.99 .16 5.31 .21 5.82 .23 Insertion of wire in contact barrel When inserting the stripped wire into the contact barrel check that no strands are left outside and that the wire is visible through the wire inspection hole in the barrel. Important : - Slide any accessories over wire strands before carrying out the following operations. - Contacts are inserted and extracted from the rear of the connector. Insertion of the contacts 1 - Engage the crimp cable / contact asembly into the longitudinal slot of the plastic tool (coloured tip). Slide the tool down the cable until the tip of the tool abuts the contact retention shoulder. 2 - Introduce the contact into the required contact cavity in the insulator, pushing tool axialy, until the contact snaps into position in clip. 3 - Withdraw the tool (from rear). Check that contact is firmly locked by pulling wire gently. When connector is fully loaded, check the position of contact tips. They should all be in the same plane. Nota : For larger sizes of cable which are stiff enough manual insertion without tool is preferable. 70 © 2011 - SOURIAU 5.31 .21 5.82 .23 5.31 .21 5.82 .23 12.5 .49 13 .51 12.5 .49 13 .51 1 2 3 Conductor insulation L = length of wire stripping L 0.5 to 0.8 mm Wire Barrel Inspection hole
8D Series Common Section Wiring instruction Extraction of the contacts 1 - Engage the appropriate cable into the longitudinal slot of the tool with the white tip towards connector. 2 - Slide the tool down towards the contact. Insert the tool in the insulator until it abuts the contact shoulder. 3 - Holding the tool-contact and cable assembly together, remove them simultaneously. Backshell tightening and slackening tools Backshell tightening pliers, part number : 8498-03 Square jaws, part number : 8500-1015 (order 2 jaws) Strap clamp : 8498-04 Spare strap : 8498-103 Tightening support Part number: 8599-0831 This tool is made up of dummy receptable housings of all 9 sizes for all key polarisation, and locates free connectors during wiring and fitting of rear accessories. 1 2 3 8498-03 8498-04 © 2011 - SOURIAU 71
Page 1:
8D Series MIL-DTL-38999 Series III
Page 5 and 6:
8D Series Overview MIL-DTL-38999: A
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 21 and 22: 8D Series Standard Series Aluminum
Page 23 and 24: 8D Series D38999 Aluminum Series MI
Page 25 and 26: 8D Series D38999 Aluminum Series Ty
Page 27 and 28: 8D Series D38999 Aluminum Series So
Page 29 and 30: 8D Series D38999 Aluminum Series No
Page 31 and 32: 8D Series D38999 Aluminum Series Du
Page 33 and 34: 8D Series 8D - D 8999 lumi D38999 A
Page 35 and 36: 8D Series D38999 Composite Series B
Page 37 and 38: 8D Series D38999 Composite Series L
Page 39 and 40: 8D Series D38999 8D - D38999 Compos
Page 41 and 42: 8D Series D38999 Stainless Steel Se
Page 43 and 44: 8D Series 8 - D 8 99 S ai less D389
Page 45 and 46: 8D Series 8D - D38999 Stai less D38
Page 47 and 48: 8D Series D38999 Titanium Series Di
Page 49 and 50: 8D Series D38999 Titanium Series Re
Page 52 and 53: 8D Series D38999 Bronze Series Conn
Page 54 and 55: 89 8D Series 9 Bro D38999 Bronze Se
Page 56 and 57: 8D Series D38999 Bronze Series Back
Page 58 and 59: 8D Series D38999 Bronze Series 58
Page 60 and 61: 8D Series D38999 Bronze Series Dumm
Page 63 and 64: 8D Series Common Section Crimp cont
Page 65 and 66: 8D Series Common Section Crimp cont
Page 67 and 68: 8D Series Common Section Coaxial co
Page 69: 8D Series Common Section Insertion
Page 73 and 74: 8D Series Common Section A Orientat
Page 75 and 76: Ct a 8D Series Common Section -X 13
Page 77 and 78: J 0 8D Series f r traigh Common Sec
Page 79 and 80: Co Co ac 8D Series C U tac Coord .
Page 81: 10 8 + 6 1 7 nY -2-81823 nate 8D Se
Page 84 and 85: 8D Series Reinforced Sealing Series
Page 86 and 87: 8D Series Hermetic Series Technical
Page 88 and 89: 8D Series Hermetic Series Note: All
Page 90 and 91: 8D Series Integrated Clinch Nuts Or
Page 92 and 93: 8D Series Double Flange Technical f
Page 94 and 95: 8D Series Double Flange Dimensions
Page 96 and 97: 8D Series PCB Contacts without Shou
Page 98 and 99: 8D Series Quadrax Contacts Technica
Page 100 and 101: 8D Series Quadrax Contacts Dimensio
Page 102 and 103: 8D Series Quadrax Contacts Contact
Page 104 and 105: 8D Series Power Contacts Connector
Page 106 and 107: 8D Series Power Contacts * Not incl
Page 108 and 109: 8D Series High Power Contacts Techn
Page 110 and 111: 8D Series High Power Contacts Order
Page 112 and 113: 8D Series High Power Contacts B E 1
Page 114 and 115: 8D Series Optical ELIO ® Contacts
Page 120 and 121:
8D Series Optical ELIO ® Contacts
Page 122 and 123:
8D Series RJ45/USB Series Connector
Page 124 and 125:
8D Series RJ45/USB Series Dimension
Page 126 and 127:
8D Series RJ45/USB Series PIN 1 PIN
Page 129 and 130:
8D Series Range Extension micro3899
Page 131 and 132:
Page 133:
show all

Souriau 8D Series - TTI Europe

Create successful ePaper yourself

Delete template?

Save as template?