150H Fork Positioner - Cascade Corporation

More documents

Recommendations

Info

I NSTALLATION 2.3 Installation Procedure Follow the steps shown to install the Fork Positioner on the truck. Read and understand all WARNINGS and CAUTION statements. If you don't understand a procedure, ask your supervisor, or call the nearest Cascade Service Department for assistance. 1 2 Unlock Attach overhead hoist A Remove banding. B Attach hoist to top of backrest as shown and lift Attachment into vertical position. C Remove bolt-on lower mounting hooks. B C quick-change lower mounting hooks (if equipped) A Remove pin and drop hooks into unlocked position. B Reinstall pin in lower hole. Guide Pin cascade ® C-675514-1 A LH lower Hook 5/8-in. (16 mm) offset on top provides max. clearance. WARNING: Make sure overhead hoist has a rated capacity of at least 2000 lbs. (910 kg.) 4 219473 Rev. 1 B FP0263.ill NOTE: Guides can be reversed to change hook-to-carriage clearance (See lower hook installation, Step 4). CL0097.ill Tighten Capscrews: Class II, III Mounting – 165 ft.-lbs. (225 Nm) Class IV Mounting – 190 ft.-lbs. (255 Nm)
I 3 Mount NSTALLATION Fork Positioner on truck A Lower Attachment onto truck carriage. B Engage upper mounting hooks. If sideshifter equipped (shown), make sure bearings are in place and centering tab engages center notch on truck carriage. ITA Class IV – 0.72–0.78 in. (18–20 mm) ITA Class IV – 0.47–0.51 in. (12–13 mm) 4 Install or engage lower hooks Tap tight into position. If sideshifter, back off 1 notch and check clearance: 3/32 in. (2.4 mm) min. 3/16 in. (4.8 mm) max. 219473 Rev. 1 5 FP0209.ill BOLT-ON TYPE QUICK-CHANGE TYPE (optional) �� Center Notch Truck Carriage Tighten Capscrews: Class IV Mounting – 190 ft.-lbs. (255 Nm) Lower Carriage Bar SS0140.ill SS0139.ill Back (Driver's) View Slide hook up to engage bar, install pin in locked position. (upper hole.) A cascade � �� B Sideshifter Upper Bearings Lower Carriage Bar SS0141.ill FP0651.ill Inspect hooks for excessive clearance. (Reverse guides to reduce clearance – see Step 2.) 3/16 in. (4.8 mm) max.
Page 1 and 2: S ERVICE MANUAL 150H Fork Positione
Page 3 and 4: I NTRODUCTION 1.1 Introduction This
Page 5: I NSTALLATION 2.2 Recommended Hydra
Page 9 and 10: I 6 NSTALLATION Prepare hoses A Det
Page 11 and 12: I NSTALLATION 11 Cycle Fork Positio
Page 13 and 14: P ERIODIC MAINTENANCE WARNING: Afte
Page 15 and 16: T ROUBLESHOOTING 4.2 Plumbing 4.2-1
Page 17 and 18: T ROUBLESHOOTING 4.4 Sideshift Func
Page 19 and 20: S ERVICE 5.1 Fork Positioner Remova
Page 21 and 22: S ERVICE 5.3 Cylinders 5.3-1 Cylind
Page 23 and 24: S ERVICE 5.3-4 Cylinder Reassembly
Page 25 and 26: S PECIFICATIONS 6.1-4 Torque Values

150H Fork Positioner - Cascade Corporation

Create successful ePaper yourself

Delete template?

Save as template?