NF8 Series - Ossh.com

More documents

Recommendations

Info

1-4 Chapter 1 NF8 Series
Hardware Setup 2-1 Chapter 2. Hardware Setup Before the Installation: Turn off the power supply switch (fully turn off the +5V standby power), or disconnect the power cord before installing or unplugging any connectors or add-on cards. Failing to do so may cause the motherboard components or add-on cards to malfunction or damaged. 2-1. Install The Motherboard Most computer chassis have a base with many mounting holes to allow motherboard to be securely attached on and at the same time, prevented from short circuits. There are two ways to attach the motherboard to the chassis base: 1. use with studs 2. or use with spacers In principle, the best way to attach the board is to use with studs. Only if you are unable to do this should you attach the board with spacers. Line up the holes on the board with the mounting holes on the chassis. If the holes line up and there are screw holes, you can attach the board with studs. If the holes line up and there are only slots, you can only attach with spacers. Take the tip of the spacers and insert them into the slots. After doing this to all the slots, you can slide the board into position aligned with slots. After the board has been positioned, check to make sure everything is OK before putting the chassis back on. ATTENTION: To prevent shorting the PCB circuit, please REMOVE the metal studs or spacers if they are already fastened on the chassis base and are without mounting-holes on the motherboard to align with. User’s Manual
Page 1 and 2: NF8 Series (NF8 Pro/NF8/NF8-V Pro/N
Page 3 and 4: Table of Contents Chapter 1. Introd
Page 5 and 6: Introduction 1-1 Chapter 1. Introdu
Page 7: Introduction 1-3 1-2. Layout Diagra
Page 11 and 12: Hardware Setup 2-3 2-3. Install Sys
Page 13 and 14: Hardware Setup 2-5 (2). FAN Power C
Page 15 and 16: Hardware Setup 2-7 (4). Front Panel
Page 17 and 18: Hardware Setup 2-9 (7). Wake-up Hea
Page 19 and 20: Hardware Setup 2-11 (9). Internal A
Page 21 and 22: Hardware Setup 2-13 (12). Serial AT
Page 23 and 24: BIOS Setup 3-1 Chapter 3. BIOS Setu
Page 25 and 26: BIOS Setup 3-3 AGP Clock(MHz): This
Page 27 and 28: BIOS Setup 3-5 IDE Channel 0 Master
Page 29 and 30: BIOS Setup 3-7 3-3. Advanced BIOS F
Page 31 and 32: BIOS Setup 3-9 3-4. Advanced Chipse
Page 33 and 34: BIOS Setup 3-11 3-5. Integrated Per
Page 35 and 36: BIOS Setup 3-13 � USB 2.0 Control
Page 37 and 38: BIOS Setup 3-15 Power On Function:
Page 39 and 40: BIOS Setup 3-17 3-7. PnP/PCI Config
Page 41 and 42: BIOS Setup 3-19 3-9. Load Fail-Safe
Page 43 and 44: Install NVIDIA nForce Chipset Drive
Page 45 and 46: Install Realtek Audio Driver B-1 Ap
Page 47 and 48: Install USB 2.0 Driver C-1 Appendix
Page 49 and 50: Install AMD64 Processor Driver D-1
Page 51 and 52: ABIT EQ (The Hardware Doctor Utilit
Page 53 and 54: FlashMenu (BIOS Update Utility) App
Page 55 and 56: NF8 NVRaid Floppy Disk Appendix G.
Page 57 and 58: Troubleshooting (Need Assistance?)
Page 59 and 60:
Troubleshooting (Need Assistance?)
Page 61 and 62:
How to Get Technical Support I-1 Ap
Page 63 and 64:
How to Get Technical Support I-3 No
show all

NF8 Series - Ossh.com

Create successful ePaper yourself

Delete template?

Save as template?