Str-k880/k900

More documents

Recommendations

Info

$@KE|\|woo|:: KX-2050$

STR-K880/K900 Ver. 1.1 Reproduction frequency range 28 - 20,000 Hz Tone Gain levels ±6 dB, 1 dB step FM tuner section Tuning range 87.5 - 108.0 MHz Antenna FM wire antenna Antenna terminals 75 ohms, unbalanced Intermediate frequency 10.7 MHz AM tuner section Tuning range Models of area code US, CND With 10-kHz tuning scale: 530 – 1,710 kHz3) With 9-kHz tuning scale: 531 – 1,710 kHz 3) Antenna Loop antenna Intermediate frequency 450 kHz Models of area code E51 With 10-kHz tuning scale: 530 – 1,610 kHz3) With 9-kHz tuning scale: 531 – 1,602 kHz3) Models of area code AEP, UK, AUS, SP, SP6 With 9-kHz tuning scale: 531 – 1,602 kHz Notes on chip component replacement • Never reuse a disconnected chip component. • Notice that the minus side of a tantalum capacitor may be damaged by heat. UNLEADED SOLDER Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size) : LEAD FREE MARK Unleaded solder has the following characteristics. • Unleaded solder melts at a temperature about 40 °C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350 °C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! • <strong>Str</strong>ong viscosity Unleaded solder is more viscou-s (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. • Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder. 2 Antenna Loop antenna Intermediate frequency 3) You can change the AM tuning scale to 9 kHz or 10 kHz. After tuning in any AM station, turn off the receiver. While holding down TUNING MODE, press ?/1. All preset stations will be erased when you change the tuning scale. To reset the scale to 10 kHz (or 9 kHz), repeat the procedure. Video section Inputs/Outputs Video: 1 Vp-p, 75 ohms COMPONENT VIDEO: Y: 1 Vp-p, 75 ohms PB/CB/B-Y: 0.7 Vp-p, 75 ohms PR/CR/R-Y: 0.7 Vp-p, 75 ohms 80 MHz HD Pass Through General Power requirements 450 kHz Area code Power requirements US, CND 120 V AC, 60 Hz AEP, UK 230 V AC, 50/60 Hz AUS 240 V AC, 50 Hz SP, SP6 230 – 240 V AC, 50/60 Hz E51 120/220/240 V AC, 50/60 Hz MODEL IDENTIFICATION – Rear Panel – Parts No. Model Part No. US model 2-663-098-0[] Canadian model 2-663-098-1[] AEP, UK models 2-663-098-2[] E51 model 2-663-098-3[] SP, SP6 models 2-663-098-4[] AUS model 2-663-098-5[] • Abbreviation AUS : Australian model CND : Canadian model E51 : Chilean and Peruvian models SP : Singapore model SP6 : Singapore and Malaysia models Power consumption Area code Power consumption US 170 W CND 230 VA AEP, UK, AUS, SP, SP6, E51 200 W Power consumption (during standby mode) 0.2 W Dimensions (w/h/d) (Approx.) 430 × 157.5 × 316 mm (167/8 × 62 /8 × 124/8 inches) including projecting parts and controls Mass (Approx.) 8.0 kg (17 lb 11 oz) Design and specifications are subject to change without notice.
SAFETY CHECK-OUT After correcting the original service problem, perform the following safety check before releasing the set to the customer: Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below. LEAKAGE TEST The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microamperes.). Leakage current can be measured by any one of three methods. 1. A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers’ instructions to use these instruments. 2. A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job. 3. Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The “limit” indication is 0.75 V, so analog meters must have an accurate low-voltage scale. The Simpson 250 and Sanwa SH-63Trd are examples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2 V AC range are suitable. (See Fig. A) 0.15 µF To Exposed Metal Parts on Set 1.5 kΩ AC voltmeter (0.75 V) Earth Ground Fig. A. Using an AC voltmeter to check AC leakage. SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ! LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COM- POSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY. TABLE OF CONTENTS STR-K880/K900 1. GENERAL ................................................................... 4 2. TEST MODE ............................................................... 12 3. DIAGRAMS ................................................................. 14 3-1. Block Diagram – MAIN Section – .................................. 16 3-2. Block Diagram – DISPLAY/POWER Section – ............. 17 3-3. Printed Wiring Board – DIGITAL Board (Side A) –....... 18 3-4. Printed Wiring Board – DIGITAL Board (Side B) –....... 19 3-5. Schematic Diagram – DIGITAL Board (1/5) – ............... 20 3-6. Schematic Diagram – DIGITAL Board (2/5) – ............... 21 3-7. Schematic Diagram – DIGITAL Board (3/5) – ............... 22 3-8. Schematic Diagram – DIGITAL Board (4/5) – ............... 23 3-9. Schematic Diagram – DIGITAL Board (5/5) – ............... 24 3-10. Printed Wiring Board – MAIN Board – .......................... 25 3-11. Schematic Diagram – MAIN Board (1/3) – .................... 26 3-12. Schematic Diagram – MAIN Board (2/3) – .................... 27 3-13. Schematic Diagram – MAIN Board (3/3) – .................... 28 3-14. Printed Wiring Boards – DISPLAY Board, POWER Board – ............................. 29 3-15. Schematic Diagrams – DISPLAY Board, POWER Board – ............................. 30 3-16. Printed Wiring Boards – STANDBY Board, AC SELECT Board – .................... 31 3-17. Printed Wiring Board – SPEAKER Board – ................... 32 3-18. Schematic Diagram – SPEAKER Board, STANDBY Board, AC SELECT Board – ....................... 33 3-19. Printed Wiring Board – SPEAKER B Board – ............... 34 3-20. Printed Wiring Boards – ADCC Board, VIDEO 3 Board – ................................. 35 3-21. Schematic Diagrams – SPEAKER B Board, ADCC Board, VIDEO 3 Board – .................................... 36 3-22. Printed Wiring Boards – VIDEO Board, HEADPHONE Board – ....................... 37 3-23. Schematic Diagram – VIDEO Board, HEADPHONE Board – ....................... 38 3-24. Printed Wiring Board – HDMI Board – .......................... 39 3-25. Schematic Diagram – HDMI Board – ............................. 40 4. EXPLODED VIEWS 4-1. Front Panel Section ......................................................... 49 4-2. Chassis Section-1 ............................................................ 50 4-3. Chassis Section-2 ............................................................ 51 5. ELECTRICAL PARTS LIST .................................. 52 About area codes The area code of the receiver you purchased is shown on the lower right portion of the rear panel (see the illustration below). L CENTER + – SURROUND BACK L + – + – R R SURROUND FRONT A SPEAKERS R L R L FRONT B SPEAKERS Area code Any differences in operation, according to the area code, are clearly indicated in the text, for example, “Models of area code AA only”. 3
Page 1: SERVICE MANUAL Ver. 1.1 2006.05 •
Page 5 and 6: About the indicators on the display
Page 7 and 8: Rear panel STR-K880 model DIGITAL O
Page 9 and 10: Name Function B ?/1 Press to turn t
Page 11 and 12: Name Function Numeric buttons Press
Page 13 and 14: VACS CONTROL Procedure: 1. While de
Page 15 and 16: STR-K880/K900 • Circuit Boards Lo
Page 17 and 18: STR-K880/K900 3-2. BLOCK DIAGRAM -
Page 19 and 20: STR-K880/K900 3-4. PRINTED WIRING B
Page 21 and 22: STR-K880/K900 3-6. SCHEMATIC DIAGRA
Page 23 and 24: STR-K880/K900 3-8. SCHEMATIC DIAGRA
Page 25 and 26: STR-K880/K900 3-10. PRINTED WIRING
Page 27 and 28: 27 27 STR-K880/K900 STR-K880/K900 3
Page 33 and 34: STR-K880/K900 3-18. SCHEMATIC DIAGR
Page 41 and 42: • IC Block Diagrams - DIGITAL Boa
Page 43 and 44: IC1452 PCM1609APT RST 37 SCKI 38 SC
Page 45 and 46: 45 STR-K880/K900 - VIDEO Board - IC
Page 47 and 48: Pin No. Pin Name I/O Description 48
Page 49 and 50: NOTE: • -XX and -X mean standardi
Page 51 and 52: 4-3. CHASSIS SECTION-2 b not k supp
Page 53 and 54:
STR-K880/K900 Ref. No. Part No. Des
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
MEMO STR-K880/K900 67
show all

Str-k880/k900

Create successful ePaper yourself

Delete template?

Save as template?