2001 DVS Fireplace - Woodman's Parts Plus
2001 DVS Fireplace - Woodman's Parts Plus
2001 DVS Fireplace - Woodman's Parts Plus
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
PAGE 10 INSTALLATION (CONT.) - For Qualified Installers Only!<br />
Facing Requirements<br />
• The combustible area above the facing must not protrude more than 3/4" from the facing. If it<br />
does, it is considered a mantel and must meet the mantel requirements listed in this manual.<br />
Bottom of<br />
Faceplate<br />
12" Min.<br />
21-9/16" Discovery & Rosario<br />
22" FPX Arch & Rect.<br />
21-1/2" Heritage Bay & Cambridge<br />
22-1/2" Salish Bay<br />
acing Over 1" Thick<br />
• If the facing material<br />
is over 1" thick (e.g.<br />
brick, river rock),<br />
install the facing<br />
around the perimeter<br />
of the face. You may<br />
wish to make a<br />
facing support (see<br />
the illustration to the<br />
right). If using an<br />
arch face, you may<br />
wish to order the<br />
optional set-up face:<br />
Arch Set-Up Face<br />
Part # 98500697<br />
������������<br />
������������<br />
������������<br />
������������<br />
������������<br />
Rectangular Face<br />
������������<br />
�������<br />
Arch Face ������������<br />
�������<br />
������������<br />
�������<br />
32" Discovery & Rosario<br />
30" FPX Arch & Rect.<br />
������������<br />
�������<br />
31-5/8" Heritage Bay<br />
30-1/2" Salish Bay<br />
������������<br />
�������<br />
33-7/8" Cambridge<br />
������������<br />
������������<br />
The fireplace requires a concrete<br />
board (or other non-combustible)<br />
extending from the header to the<br />
floor and to the framing members on<br />
both sides. Do not use sheetrock,<br />
plywood or other combustible<br />
material.<br />
Header<br />
Non-combustible Facing<br />
6" Min.<br />
(both sides)<br />
��������������<br />
The brick facing must meet the same requirements<br />
listed in “Facing Requirements” above.<br />
��������������<br />
������������<br />
��������������<br />
������������<br />
��������������<br />
������������<br />
��������������<br />
������������<br />
��������������<br />
���������������<br />
��������������<br />
���������������<br />
������<br />
������<br />
������ ���<br />
���������������<br />
������<br />
������<br />
������ ���<br />
������<br />
������<br />
������ ���<br />
������������������<br />
������<br />
������ ���<br />
Center<br />
Line<br />
������������������<br />
������������ ���<br />
������������������<br />
������������ ���<br />
������������������<br />
������������<br />
�������������<br />
������������� ���<br />
������������������<br />
������������<br />
�������������<br />
������������� ���<br />
������������������<br />
������ ������������<br />
�������������<br />
�������������<br />
�� ������������������<br />
������ ������������<br />
�������������<br />
�������������<br />
Arch Faces<br />
Use the optional Arch<br />
Set-Up Face available<br />
������������������<br />
�������������������<br />
�������������<br />
from Travis<br />
1-1/2” Industries.<br />
������������������<br />
������ �� �������������<br />
�������������<br />
�� �������������<br />
Rectangular Faces<br />
Make a facing support using<br />
2x4’s. It should be 1/8” larger<br />
than the finished face. NOTE:<br />
The bottom of the face is 1-1/2”<br />
above the base of the fireplace.<br />
Note: if using a brick hearth, the fireplace will need to be raised to accommodate the 1-1/2” gap betwen the<br />
face and the base of the fireplace. For 2-1/2” thick brick this works out to approximately 1-1/8”.<br />
Face Sizing:<br />
HEIGHT:<br />
21-9/16" Lopi Discovery Face<br />
21-9/16" Avalon Avanti Face<br />
22" FPX 32 Arch Face<br />
22" FPX 32 Rect. Face<br />
WIDTH:<br />
32" Lopi Discovery Face<br />
32" Avalon Avanti Face<br />
30" FPX 32 Arch Face<br />
30" FPX 32 Rect. Face