2001 DVS Fireplace - Woodman's Parts Plus

More documents

Recommendations

Info

PAGE 6 INSTALLATION - For Qualified Installers Only! Installation Preparation ! Failure to follow all of the requirements may result in property damage, bodily injury, or even death. ! This appliance must be installed in accordance with all local codes, if any; if not, follow ANSI Z223.1 and NFPA 54(88). ! In Manufactured or Mobile Homes must confirm with: In USA, Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280; In Canada, CSA Z240.4 and Gas- Equipped Recreational Vehicles and Mobile Housing. This appliance may be installed in Manufactured Housing only after the home is site located. ! The DVS Fireplace is designed to operate on natural gas, or propane (LP). ! All exhaust gases must be vented outside the structure of the living-area. Combustion air is drawn from outside the living-area structure. ! Notify your insurance company before hooking up this fireplace. ! The requirements listed below are divided into sections. All requirements must be met simultaneously. The order of installation is not rigid – the qualified installer should follow the procedure best suited for the installation. Packing List • Propane Conversion Kit • Log Set (2 Logs, 2 Twigs, Bag of Coals, Coal Trays) • Restrictor Adjuster Rod • Flex Tube with Pipe Adapter Installation Overview The faceplate must be 6" minimum from side walls. See "Gas Line Installation" Non-combustible facing (see "Facing Requirements") Drywall See "Mantel Requirements" See "Hearth Requirements" See "Fireplace Placement Requirements" Optional thermostat or remote control wire. Additional Items Required for Installation • Face (includes attachment screws) • Direct Vent (Simpson Dura-Vent Ph. # 800 835-4429) • Gas Line Equipment (shutoff valve, pipe, etc.) • Electrical Connection Equipment (min. 18 gauge, grounded line) See "Vent Requirements" �� See "Electrical Connection" See "Horizontal Termination Requirements" See "Acceptable Vent Lengths" Insulation must not fill the spaces between the stand-offs Nail Down Plate See "Minimum Framing Dimensions"
Fireplace Placement Requirements Setting Up the Standoffs ! AFTER BEFORE INSTALLATION (CONT.) - For Qualified Installers Only! PAGE 7 The standoffs are shipped in the flat position. Make sure to follow the instructions below before installing the fireplace. a Standoff 1 2 Bend the standofff in the sequence shown. 3 1/4" Nutdriver b Remove the screw below the standoff. c Replace the screw to secure the standoff. WARNING : Failure to set up the standoffs will result in an extreme fire hazard . Minimum Framing Dimensions • The 1/2" stand-offs on the back and sides and 6- 1/4" stand-offs on the top of the fireplace are designed to separate the fireplace from the framing members. These stand-offs may contact the framing members but no material may be placed between the stand-offs. • Fireplace must be installed on a level surface capable of supporting the fireplace and vent • Fireplace must be placed directly on wood or noncombustible surface (not on linoleum or carpet) • Due to the high temperature of the fireplace, it should be located out of traffic and away from furniture and draperies. 35" 19-5/8" 37-1/4" NOTE: when using an elbow off the top of the fireplace, allow for a 2" clearance above the vent (1" to the sides and bottom). 36" From Base of Fireplace. NOTE: when venting to the rear, allow a min. 8-5/8" gap centered behind the fireplace (for the vent and wall thimble). Gas Line (the inlet is 7-3/4" behind the framing and 2-5/8" above the base of the fireplace (see "Gas Line Connection" for details). Route the electrical line (and optional thermostat or remote control wire) to the right of the fireplace. Clearances • When installed, walls in front of the fireplace must be a minimum 6" to the side of the faceplate. • Fireplace must be placed so that no combustibles are within, or can swing within 36" of the front of the fireplace (e.g. drapes, doors) • Fireplace must be placed so the vents below and above the glass do not become blocked • This heater may be placed in a bedroom. Please be aware of the large amount of heat this appliance produces when determining a location.
Page 1 and 2: ��
Page 3 and 4: �� • Do
Page 5: Features: - Works During Power Outa
Page 9 and 10: Hearth Requirements Min. 1-1/4” M
Page 11 and 12: Facing Detail INSTALLATION (CONT.)
Page 13 and 14: Facing and Hearth Examples Side Vie
Page 15 and 16: Tile Hearths Mantel Requirements IN
Page 17 and 18: INSTALLATION (CONT.) - For Qualifie
Page 23 and 24: Electrical Connection INSTALLATION
Page 25 and 26: FINALIZING THE INSTALLATION (CONT.)
Page 27 and 28: FINALIZING THE INSTALLATION (CONT.)
Page 29 and 30: Starting The Pilot Flame The pilot
Page 31 and 32: Adjusting the Blower Speed OPERATIO
Page 33 and 34: TROUBLESHOOTING PAGE 33 Problem: Po
Page 35 and 36: Wiring Diagram Brown Jumper Wire (M
Page 37 and 38: The listing label can be found on t
Page 39 and 40: OPTIONAL EQUIPMENT (CONTINUED) PAGE
Page 41 and 42: OPTIONAL EQUIPMENT (CONTINUED) PAGE
Page 43 and 44: ADDENDUM PAGE 43 Altitude Considera

2001 DVS Fireplace - Woodman's Parts Plus

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?