2001 DVS Fireplace - Woodman's Parts Plus

More documents

Recommendations

Info

PAGE 38 OPTIONAL EQUIPMENT Propane Conversion Kit The propane conversion kit should be installed prior to installing the heater and gas inlet (if not, shut off gas and disconnect the gas inlet). Items Needed For Assembly • 1/4" Nutdriver • 7/16" and 1/2" Open End Wrench • Standard Screwdriver • Phillips Screwdriver • Micro (1/16") Standard Screwdriver • Thread sealant Packing List • Leak Testing Equipment • LP Orifice (.0625" diameter) • LP Pilot Orifice • Replacement Regulator • Two Replacement Screws Installation Instructions • Regulator Gasket • LP Label 1 Remove the glass (see page 24). 2 Reach into the firebox and remove the ember shelf (see the illustration to the right). 3 Reach into the firebox and remove the burner (see the illustration below). Place the ember shelf around the burner (note: there will be a gap between the shelf and the burner). This baffle, which is loosely attached, must hang down behind the right rear log pin. Place the burner so the mixing tube slides onto the orifice. �� Make sure this pin inserts into the hole in the bottom of the burner. �� Slide the air shutter all the way to the right.
OPTIONAL EQUIPMENT (CONTINUED) PAGE 39 4 Follow the directions below to remove the natural gas orifice. Apply thread sealant to the LP orifice (.0625 dia. - it has ".0625" stamped on it) and tighten in place with a 1/2" open end wrench. Replace the spring. Slide the adjustable shutter back in place. Use a 1/2” open end wrench to unscrew the burner orifice. 5/16” 5 Replace the burner pan and ember shelf. 1/2" Wrench NOTE: Screw the LP orifice in so the orifice shoulder protrudes 5/16” (indicating full insertion). The new LP orifice has “.0625” stamped on it. .0625 37 Apply thread sealant to the new orifice and install. The old NG orifice has “37” stamped on it. 6 Remove the pilot orifice following the instructions below. Replace with the propane pilot orifice. a Lift the pilot hood off the pilot assembly. b Use a hex wrench to unscrew the orifice. 5/32" Hex c Remove the orifice and replace with the LP orifice. Screw the orifice all the way in and replace the pilot hood. NOTE: when re-attaching, this pin lines up with the notch in the pilot hood. 35 Orifice Identification: LP (Propane) Orifice 35 NG (Natural Gas) Orifice 7 Replace the pilot assembly (follow the instructions in step 6 in reverse order). Make sure the pilot assembly gasket is placed correctly. 8 Install the logs and embers. Replace the glass. 62
Page 1 and 2: ��
Page 3 and 4: �� • Do
Page 5 and 6: Features: - Works During Power Outa
Page 7 and 8: Fireplace Placement Requirements Se
Page 9 and 10: Hearth Requirements Min. 1-1/4” M
Page 11 and 12: Facing Detail INSTALLATION (CONT.)
Page 13 and 14: Facing and Hearth Examples Side Vie
Page 15 and 16: Tile Hearths Mantel Requirements IN
Page 17 and 18: INSTALLATION (CONT.) - For Qualifie
Page 23 and 24: Electrical Connection INSTALLATION
Page 25 and 26: FINALIZING THE INSTALLATION (CONT.)
Page 27 and 28: FINALIZING THE INSTALLATION (CONT.)
Page 29 and 30: Starting The Pilot Flame The pilot
Page 31 and 32: Adjusting the Blower Speed OPERATIO
Page 33 and 34: TROUBLESHOOTING PAGE 33 Problem: Po
Page 35 and 36: Wiring Diagram Brown Jumper Wire (M
Page 37: The listing label can be found on t
Page 41 and 42: OPTIONAL EQUIPMENT (CONTINUED) PAGE
Page 43 and 44: ADDENDUM PAGE 43 Altitude Considera

2001 DVS Fireplace - Woodman's Parts Plus

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?