CATALOGUE TIME and MONITORING RELAYS - Hiquel

More documents

Recommendations

Info

3 phase monitoring relay (phase failure, sequence) 2:14 1or2 1 or 2 3 DIN Phase 100% L1 0% 100% Phase L2 0% Phase 100% L3 0% X01.00 Function Contol relay active Control relay passive Contact closed Contact open R L1 L1 L2 L2 L3 L3 L3 R Phase Sequence/Failure L1 L2 11 12 14 R R 21 22 24 TCP-SF HIGH QUALITY ELECTRONICS overview Phase failure relay to monitor 3-wire, 3-phase systems for the failure of one or more phase and the correct phase rotation (L1, L2, L3) The TCP-SF detects if the phase sequence is correct and that no phase has failed. If this is the case, the output relay R energises and the yellow LED is illuminated. At a loss of one phase the output relay R de-energises. The relay energises again, when the failed phase/phases resume. The control relay will not detect a phase failure with a regenerated voltage present on the failed phase. (Suitable for lift/elevator applications where the car must continue to the next stop and then not restart) supply voltage variation frequency range duty cycle reset time TCP-SF relay type 3x200-440Vac output relay spec. 230V~ Ie AC-15 120V~ L1 Ie AC-15 240V~ L3 L2 Ie DC-13 24V= part no supply output TCP-SF 3x 200-440V~ 6VA SPCO TCP-SF2 3x 200-440V~ 6VA DPCO detects phase failure and phase sequence SPCO output max. 8A measuring voltage without neutral does not detect phase failure with regenerated voltage present LED indicators for power supply, relay and reaction timer 22.5mm DIN rail mount housing specification nominal voltage +/-10% 48-63Hz 100% < 25ms 1 2 8A 8A 1,5A 1,5A 1,5A 1,5A 1A 1A expected life time DPCO SPCO mechanical 30x10 operating conditions -20 to +60°C non condensing 6 resp. 30x10 7 operations screws pozidrive 1 screw tightening torque 0,6..0,8Nm * EN 60947-5-1 VDE 0435 ordering information relay type Gehäusetypen 1 - 2 - housing types A B HIQUEL 2009
TCP-M overview detects phase failure, phase sequence phase asymmetry and over-temperature using PTC sensors detects phase failure with regenerated voltage present up to 6 PTC sensors in series DPCO output max. 6A fixed asymmetry alarm >10% no neutral connection required adjustable reaction timer 0.1 - 10s LED indicators for power supply, relay and reaction timer 45mm DIN rail mount housing supply voltage variation frequency range duty cycle response/delay time reset time max. measuring voltage max. resistance triggering threshold reset threshold short circuit detection output relay specification Ue/Ie AC-15 Ue/Ie DC-13 expected life time mechanical electrical operating conditions specification nominal voltage +10% / -15% 48-63Hz 100% < 300ms < 500ms < 2,5V 1500 Ohm (6 sensors) 3100 Ohm 1650 Ohm 0-20Ohm max. 6A 230V~ 120V/4A 240V/3A 24V/2A DPCO SPCO 2x10 6 resp. 1 x 10 7 operations resp. 1 x 10 5 operations 1x10 5 -20 to 60°C non condesning * EN 60947-5-1 VDE 0435 ordering information part no supply output TCP-M 3x400Vac 3x 400V~ 2,5VA DPCO TCP-M 3x230Vac 3x 230V~ 2,5VA DPCO TCP-M 3x440Vac 3x 440V~ 2,5VA DPCO * The measurement input is galvanically isolated from the power supply Phase 100% L1 0% 100% Phase L2 0% Phase 100% L3 0% Asymmetry R TCP-M U 3x230V AC HIQUEL 2009 X01.00 >10% < 75% L1 - N Phase Sequence + Thermistor Motor Protection HIGH QUALITY ELECTRONICS R 0,1 Time 10 0,1 - 10s < 75% L2 - N L1 L3 L2 PTC DIN44081 T1 ...6 T2 1... < 75% L3 - N t t t t Control relay for phase failure and thermistor protection The TCP-M monitors phase sequence, phase failure and phase asymmetry, and is used with PTC sensors to provide over temperature protection for motors and other equipment. When the phase sequence is correct, all phases are detected, and the resistance of the PTC sensors on the input T1 - T2 is within the correct range, the output relay R energises. At a loss of one phase (> Vn x 0.75 ), or the detection of an asymmetry imbalance >10%, or when the resistance of the PTC sensors exceeds the triggering threshold (3100 Ohm) the reaction time t starts. R (Ohm) At the end of time t the output relay R 4000 de-energises. Time t is adjustable between 0.1s and 10s and is used to 1330 time out short transients which would otherwise cause nuisance tripping. 550 The relay energises again when phase L1, L2 and L3 return to the 250 correct range and the resistance of the sensors falls below the reset threshold (1650 Ohms). 20 Function Control relay active Control relay passive Contact closed Contact open -20 0 TNF: nominal triggering temperature L1 L1 L2 L2 TNF-20 TNF-5 TNF+5 TNF+15 L3 L3 T1 sup. galv. Gehäusetypen iso* yes yes yes yes yes no L3 °C L1 T2 L2 The control relay will detect a phase failure even with a regenerated voltage present on the failed phase (no detection on request). 11 PTC(1...6) DIN 44081 12 R R 14 21 22 24 housing types C C C 2 3 PTC DIN C US 2:15 3 phase failure and thermistor motor protection
Page 1 and 2: World of Automation Chapter 1: Gene
Page 3 and 4: 2 2 DIN 11 RTC IP50 C PT100 PTC 3 U
Page 5 and 6: World of Automation Chapter 2: Moni
Page 7 and 8: in-case Series in 2:01 U 0-10V out
Page 9 and 10: TCC-H overview AC or DC over or und
Page 11 and 12: TCC-H2 overview AC or DC over or un
Page 13 and 14: ICV overview AC or DC voltage monit
Page 15 and 16: TCV-W overview AC or DC over or und
Page 17 and 18: module overview HIQUEL 2009 X01.00
Page 19: TCP overview detects phase failure,
Page 23 and 24: TCP-V/PCP-V overview detects phase
Page 25 and 26: TCP-3N overview for 3-wire and 4-wi
Page 27 and 28: TCL overview monitors one or two le
Page 29 and 30: TCL-3 overview monitors two or thre
Page 31 and 32: TCV-SK overview safety edge monitor
Page 33 and 34: TCM overview thermistor motor prote
Page 35 and 36: TCS overview under speed control wi
Page 37 and 38: TCE overview sensor pulse extension
Page 39 and 40: TPS/UPS overview output 24V= input
Page 41 and 42: Index 3:00 HIGH QUALITY ELECTRONICS
Page 43 and 44: ITM216 overview multi-function timi
Page 45 and 46: TM overview single, dual, multi & z
Page 47 and 48: TR overview single or dual supply v
Page 49 and 50: TW overview single or dual supply v
Page 51 and 52: TA overview single or dual supply v
Page 53 and 54: TS overview single or dual supply v
Page 55 and 56: TI overview “pulse first” or
Page 57 and 58: DES/PES/TES overview supply voltage
Page 59 and 60: PRER2/TOE/TOR dual voltage supply 2
Page 61 and 62: Index 4 Chapter .01 .02 .03 .04 .05
Page 63 and 64: Multi-voltage relay, 24-240vac/dc 4
Page 65 and 66: trigger relay in 11.25mm housing in
Page 67 and 68: 2 speed fan controller 4:06 2 DIN L
Page 69 and 70: temperature transducer for thermoco
Page 71 and 72:
isolated strain gauge input module
Page 73 and 74:
diode arrays 4:12 11 DIN X01.00 TV.
Page 75 and 76:
5 Chapter5 .01 .02 .03 .04 Index :
Page 77 and 78:
ESG overview single-phase speed con
Page 79:
L1 L1 N L N Power LA M 1 M1 example
show all

CATALOGUE TIME and MONITORING RELAYS - Hiquel

Create successful ePaper yourself

Delete template?

Save as template?