CATALOGUE TIME and MONITORING RELAYS - Hiquel

More documents

Recommendations

Info

ANU/ANI overview supply voltage 24V~= feedback contact for manual or automatic mode protection against incorrect connection short circuit protection LED indicator proportional to output level 22.5mm DIN rail mount housing specification supply voltage variation nominal voltage +20% / -15% frequency range 48-63Hz duty cycle 100% nominal current 24V~/35mA 24V=/11mA contact material silver alloy switch S1-S2 28V~=/2A current consumption max. YR 10VDC 2mA screws pozidrive 1 screw tightening torque 0,6..0,8Nm operating conditions -20 to +60°C non condensing ordering information Description: ANU/ANI are used with automatic control systems (BMS, PLC, PC) that provide a 0-10V or 0-20mA signal for controlling variables such as temperature, speed, position etc. In automatic mode (“Auto”) the analogue signal from the control system (terminals YR & ) is re-transmitted to the controlled device (ratio 1:1). In manual mode (“Manu”) the analogue signal from the control system is isolated and the ANU/ANI inject a signal (terminals Y & ) which can be adjusted from 0 to 10V or 0-20mA by the potentiometer. part no supply output relay type Gehäusetypen housing type ANU 24V~=
2 speed fan controller 4:06 2 DIN L N S1 S2 K1 K2 S2 K1 K2 S1 S2 K1 K2 Description: The LSM was designed specifically to control two-speed fan motors. The LSM is controlled by a two-position switch, which is connected directly to the LSM (S1, S2). The motor contactors are controlled by the two outputs (K1, K2). The LSM will automatically control the speed selection so that the operator cannot switch the fan on from stand-still to high speed, or off when running in high speed. S1 The 3 functions are: t1 t1 50msec Switch directly from Level 2 to Level 1 S2 50msec Switch to 0(Off) 50msec max. switch time from S1 to S2 = 250msec A2 A1 t2 1.) In switch position 1 the motor will run in low speed during the set time t1. After the time t1 has expired it is possible to switch over to position 2 for high speed. The switch over time is max. 250 msec. If this is exceeded the LSM goes to function 2. 2.) If switch position 2 (high speed) is selected before switch position 1, the motor will be forced to run for the time t1(low speed). After t1 there will be an interval of 50 msec before the motor goes into high speed. Supply A1-A2 = K1 > 3.) Once in high speed, if the input is switched from position 2 to position 1 Or 0 (=stop), the high speed contact will switch off and the motor will be free wheel for the duration of timer t2 after which the low speed contact will switch on if the switch is in position 1, or will coast to a stop if switch position 0 is selected. K2 LSM U 230VAC 1 1 15 t1 t2 30 sec 60 sec Stufe 1 Stufe 2 Fan Controller HIGH QUALITY ELECTRONICS LSM overview power supply 230V~ 2 adjustable timers 2 relay outputs 230V~ LED indicators for level 1+2 22.5mm DIN rail mount housing specification supply voltage varation frequency range duty cycle repeat accuracy output relay specification relay type Ie AC-15* Ie AC-15* Ie DC-13* expected life time mechanical electrical screws 120V~ 240V~ nominal voltage +10% / -15% 48-63Hz 100%
Page 1 and 2:
World of Automation Chapter 1: Gene
Page 3 and 4:
2 2 DIN 11 RTC IP50 C PT100 PTC 3 U
Page 5 and 6:
World of Automation Chapter 2: Moni
Page 7 and 8:
in-case Series in 2:01 U 0-10V out
Page 9 and 10:
TCC-H overview AC or DC over or und
Page 11 and 12:
TCC-H2 overview AC or DC over or un
Page 13 and 14:
ICV overview AC or DC voltage monit
Page 15 and 16: TCV-W overview AC or DC over or und
Page 17 and 18: module overview HIQUEL 2009 X01.00
Page 19 and 20: TCP overview detects phase failure,
Page 21 and 22: TCP-M overview detects phase failur
Page 23 and 24: TCP-V/PCP-V overview detects phase
Page 25 and 26: TCP-3N overview for 3-wire and 4-wi
Page 27 and 28: TCL overview monitors one or two le
Page 29 and 30: TCL-3 overview monitors two or thre
Page 31 and 32: TCV-SK overview safety edge monitor
Page 33 and 34: TCM overview thermistor motor prote
Page 35 and 36: TCS overview under speed control wi
Page 37 and 38: TCE overview sensor pulse extension
Page 39 and 40: TPS/UPS overview output 24V= input
Page 41 and 42: Index 3:00 HIGH QUALITY ELECTRONICS
Page 43 and 44: ITM216 overview multi-function timi
Page 45 and 46: TM overview single, dual, multi & z
Page 47 and 48: TR overview single or dual supply v
Page 49 and 50: TW overview single or dual supply v
Page 51 and 52: TA overview single or dual supply v
Page 53 and 54: TS overview single or dual supply v
Page 55 and 56: TI overview “pulse first” or
Page 57 and 58: DES/PES/TES overview supply voltage
Page 59 and 60: PRER2/TOE/TOR dual voltage supply 2
Page 61 and 62: Index 4 Chapter .01 .02 .03 .04 .05
Page 63 and 64: Multi-voltage relay, 24-240vac/dc 4
Page 65: trigger relay in 11.25mm housing in
Page 69 and 70: temperature transducer for thermoco
Page 71 and 72: isolated strain gauge input module
Page 73 and 74: diode arrays 4:12 11 DIN X01.00 TV.
Page 75 and 76: 5 Chapter5 .01 .02 .03 .04 Index :
Page 77 and 78: ESG overview single-phase speed con
Page 79: L1 L1 N L N Power LA M 1 M1 example
show all

CATALOGUE TIME and MONITORING RELAYS - Hiquel

Create successful ePaper yourself

Delete template?

Save as template?