KEMPEROL® 1K-PUR Waterproofing - KEMPER SYSTEM

More documents

Recommendations

Info

KEMPERTEC ® FPO- Primer Uses � For excellent adhesion between polyolefin plastics (FPO/TPO) and following KEMPEROL ® products - KEMPEROL ® 1K-PUR Waterproofing System - KEMPEROL ® 2K-PUR Waterproofing System � For new construction and remedial projects Features � Quickly drying � Excellent adhesion on FPO sheets Composition Bonding agent dissolved in toluene. Pack sizes 500 g, 1 kg und 3 kg units. Shelf Life Can be stored unopened for up to 6 months in a cool, dry, frost-free place. Properties Form liquid Colour transparent Workability period* [min] approx. 5 Rainproof* after [min] approx. 30 Can be walked on* after [min] approx. 30 Next coat can be applied after* [min] approx. 30 * Values obtained at a temperature of 23 °C - 50 % rel. humidity. May vary according to weather conditions such as wind, humidity and temperature. Usage guide Depending on the nature of the substrate: approx. 50 g/m². Application The substrate must be dry, sound and free from any material that would hinder adhesion and must be prepared according to Technical Information TI 21 - Substrate Preparation. Clean surface with KEMPERTEC ® MEK Cleaning Agent. Warning: KEMPERTEC ® FPO-Primer is not appropriate for every substrate! This primer is especially developed for polyolefin plastics! Apply only when substrate and ambient temperatures exceed 5 °C and are declining. During application the surface temperature must be 3 °C above the dew point. If the substrate temperature is below or at the dew point temperature then moisture can form at the surface which can affect coating adhesion and cure. (Please refer to DIN 4108 - 5 Tab.1 for a dew point graph). Prime in one operation until the pores are closed. Distribute with a perlon roller so that material accumulation is avoided. Provided that the primer is dry and tack-free, additional suitable KEMPER SYSTEM waterproofing products (KEMPEROL ® 2K-PUR and KEMPEROL ® 1K-PUR Waterproofing) should be applied after 15 - 30 minutes - depending on the weather conditions, wind humidity and temperature. The KEMPEROL ® membrane has to be applied within the next 24 hours or separating effects can occur.
Personal protective equipment should be worn. Clean the tools immediately after use with KEMPERTEC ® MEK Cleaning Agent. Clean your hands and rub KEMPER SYSTEM skin care cream into the skin. Remark Please consider the following technical information: - TI 21 - substrate preparation - TI 23 - solvent-based products Important notice Adhesion tests on other plastic sheets (EPDM, PIB etc..) have already been made. Before applying the FPO primer on further sheets please consult KEMPER SYSTEM Ltd.! The safety data sheets, identification of the units, hazard warnings and safety recommendations on the units must be observed during transportation, storage and application. The BG-Chemie technical information must be observed for application. Do not allow into the sewer system or into the ground. Cannot be used in swimming pools! Disposal Liquid EWC 08 04 09 Cured EWC 08 04 10 General information The times given are reduced with higher and increased with lower surrounding and work surface temperatures. We guarantee the consistent high quality of our products. KEMPER SYSTEM products must not be mixed with other manufacturers´ products. The technical information and application instructions contained herein reflect the current level of knowledge and experience with our products. In each case, the new edition supersedes the previous technical information and renders it invalid. It is therefore necessary that you always have to hand the current code of practice. When using our products, a detailed, object-related and qualified inspection is required in each individual case in order to determine whether the product and / or application technology in question meets the specific requirements and purposes. We are liable only for our products being free from faults - correct application of our products therefore falls entirely within your scope of liability and responsibility. Our products are sold exclusively on the basis of our conditions of sale and delivery. Published: Vellmar, August 2009 ______________________________________________________________________________________________________________ KEMPER SYSTEM GmbH & Co. KG · Holländische Straße 32-36 · D-34246 Vellmar · Tel. +49-(0)561-82950 · Fax +49-(0)561-829510 www.kemper-system.com · post@kemper-system.com · Certified according to DIN EN ISO 9001:2000 and DIN EN ISO 14001
Page 1 and 2: KEMPEROL ® 1K-PUR Waterproofing Us
Page 3 and 4: KEMPERTEC ® 1K Thinner Uses � Fo
Page 5 and 6: KEMPEROL ® 120 Fleece Uses � As
Page 7 and 8: KEMPEROL ® 200 Fleece Uses � As
Page 9 and 10: KEMPEROL ® RS Reinforcement Strip
Page 11 and 12: Priming Recommendation KEMPEROL 1K-
Page 13 and 14: Remove the bag from the aluminium p
Page 15 and 16: A. Packaging: 1,5 kg-sachet: Remove
Page 17 and 18: Cut off one corner of the bag and p
Page 19 and 20: occur. To avoid these separating ef
Page 21: humidity) and provided that the pri
Page 25 and 26: General information We guarantee th
Page 27 and 28: Solvents containing KEMPERTEC ® ,
Page 29 and 30: With KEMPERTEC ® EP-Primer, the pr
Page 31 and 32: KEMPEROL ® waterproofing systems a
Page 33 and 34: 4. Cracks in the substrate On subst
Page 35 and 36: therefore falls entirely within you
Page 37 and 38: Product Estimated use Estimated tim
Page 39 and 40: Product Estimated use Estimated tim
Page 41 and 42: Substance solid Solution liquid UP

KEMPEROL® 1K-PUR Waterproofing - KEMPER SYSTEM

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?