ENFRIADORA AIRE/AGUA EF COMPACTA - Ferromar

More documents

Recommendations

Info

ENGLISHExpansionvalveVÁLVULAEXPANSIÓNFilterFILTRODEPOSITOLIQUIDOSALIDA Water Output AGUAFSEvaporator(water)EVAPORADOR (AGUA)Water InputENTRADA AGUATTLPSOBUSDECARGAASP.BATERIACONDENSADORABatterycondenserOBUSDECARGADESC.COMPRESORCompressorHPSOBUSDECARGAA full-flow shut-off valve should be installed on each of the hydraulic elements in the equipment,so that each of these may be isolated if needed (for repairs, substitutions, etc.) without the need todrain the circuit.Anti-vibration dampers should be installed in the inlet and outlet of the machine, in order to avoidvibrations which may cause cracks or breakage in the hydraulic connections.In order to avoid possible breakage, do not force the PVC tubes connected to the water supply.15. PROCEDURES AND START-UPWhen setting-up, the electrical connections, as well as the general power supply and voltage,should be verified.Verify that the hydraulic connections are correct.Give power to the equipment by connecting the general power switch on the outside of themachine. Once the machine is connected, verify the intensity absorbed by the phases.It is important to comment that this equipment includes compressor casing resistance, so theequipment must be connected to main power at least 1 hour before the equipment is put in serviceso that the compressors oil reaches its optimum conditions and can lubricate components of thecompressor.In the case of three-phase machine, equipment includes a relay phase control, which ensures thecorrect compressor rotation direction. If the regulator indicates that the compressor is running andit does not, then it is required to invert phases.With the machine running, verify the intensities absorbed by the resistors and electric motors,making sure they do not exceed the limits mentioned in the technical specification sheet.Make sure that there is no gap between the currents of the different phases except for those due tosingle phase circuits.© TALLERES DEL AGUA S.L. 2008. TODOS LOS DERECHOS RESERVADOS. DOCUMENTO CONFIDENCIAL Y EN PROPIEDAD.Page 42 of 50
ENGLISHHigh and low pressure switches should be installed in the cooling circuit and verify the refrigerantcharge (Refrigerant Charge section).To stop the equipment, disconnect switch on / off.16. PREVENTIVE MAINTENANCE• A record should be kept of each element repaired or substituted as well as of all maintenanceand repairs.• DISCONNECT THE EQUIPMENT FROM THE POWER SUPPLY before performing anymaintenance procedures.• The surface of the exterior panels may be cleaned with a soft cloth and non-abrasive cleaner.• The machine has been designed to work outdoors or indoors.• It is important to place the equipment on a stable and protected from flooding location.WARNING: in the case that the equipment will be shutdown for a long period of time, werecommend you remove the equipment or periodically ventilate the area where the equipment islocated. This is because the humid and often corrosive (chlorinated) areas where the equipment islocated may lead to premature deterioration of the electrical components. The warranty does notcover damage due to prolonged exposure to humid and corrosive atmospheres.Aspects to consider:CONDENSER BATTERY:The units should be kept clean and free of obstacles which may hinder the circulation of airthrough them. In order to clean them, use water (no pressure) and non-abrasive detergents orcleaning liquids made specifically for them (consult the manufacturer).COMPRESSOR:Oil level must be checked on compressor models that include oil viewer.Ensure that the Compressor casing resistance does work properly.EVAPORATION UNIT:Install the chemical doser at the exit of the equipment, as far as possible and under the exit level.Never on the inlet of the equipment pump, thus would damage the evaporator unit.Do not set concentrated chemical products in the skimmers that could attack the Titanium includein the condenser.In cold weathers where froze is usual, it is necessary to purge all the cleaning and heatingelements. In order to do that, the condenser includes a plug to purge it.FAN:Verify the flows of the fan each year.Clean the louvers of the fan as well as the protection grill regularly.© TALLERES DEL AGUA S.L. 2008. TODOS LOS DERECHOS RESERVADOS. DOCUMENTO CONFIDENCIAL Y EN PROPIEDAD.Page 43 of 50
Page 1: ENFRIADORA AIRE/AGUA - SERIES EF ·
Page 4 and 5: ESPAÑOLINDICE1. INTRODUCCION .....
Page 6 and 7: ESPAÑOLENFRIADORA AIRE/AGUA EF COM
Page 8 and 9: ESPAÑOL4. CARACTERISTICAS TECNICAS
Page 10 and 11: ESPAÑOLconfirmamos su entrada. A c
Page 12 and 13: ESPAÑOLIntroduciendo la clave de a
Page 14 and 15: ESPAÑOLREGULADOR ELECTRONICO DIGIT
Page 16 and 17: ESPAÑOL10. COMPROBACIÓN DEL EMBAL
Page 18 and 19: ALIMENTACION GENERALMODELOSECCIÓN
Page 20 and 21: ESPAÑOLSe deben instalar llaves de
Page 22 and 23: ESPAÑOLPresostato de alta abierto:
Page 24 and 25: ESPAÑOL8.- De vez en cuando, cerra
Page 26 and 27: ESPAÑOL20. RECICLAJE DEL PRODUCTOE
Page 28 and 29: ENGLISHAIR/WATER COOLER EFEF SERIES
Page 30 and 31: 4. TECHNICAL CHARACTERISTICSENGLISH
Page 32 and 33: ENGLISHCONSIGNEE Menu:To modify the
Page 34 and 35: ENGLISHIn this Submenu it would be
Page 36 and 37: ENGLISHDIGITAL ELECTRONIC REGULATOR
Page 38 and 39: ENGLISH10. PACKAGING INSPECTIONThis
Page 40 and 41: GENERAL POWERMODELSECTION (mm 2 )VO
Page 44 and 45: ENGLISHELECTRICAL PANEL:Verify all
Page 46 and 47: ENGLISHDRAINING THE COOLING CIRCUIT
Page 48 and 49: ENGLISH20. PRODUCT RECYCLINGThis un
Page 50: NOS RESERVAMOS EL DERECHO DE CAMBIA

ENFRIADORA AIRE/AGUA EF COMPACTA - Ferromar

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?