1 - Nuova Simonelli

ENGLISH
• COFFEE BOILER TEMPERATURE: the
current temperature of the coffee boiler
is visualized.
• UNIT TEMPERATURE: the current temperature
of the coffee unit is visualized
• COFFEE GROUND No: the coffee
ground number within the drawer is
visualized
• MAIN. SOFTENER FILTER: the number
of litres of water utilized (with the “U15”
key inserted and pressing the RESET
button for 5 seconds straight the number
of litres and the anti-scaling filter alarm
are reset. The display will read “0”)
• MAINTENANCE CYCLES: the number
of unit cycles left before the maintenance
alarm will be turned on, is visualized
(with the “U15” key inserted and by
pressing the button for 5 seconds straight
the number of cycles and the maintenance
alarm programmed during
installation procedures can be reset)
At the end of the visualization you will return
to the “SYSTEM DATA READ” menu.
DOSE PROGRAMMING
By means of the ▼ and ▲ buttons go to the
DOSE PROGRAMMING option, then press
the ENTER button to confirm and proceed
to selecting the buttons to program.
Button selection
The buttons , , , ,
44
, , (version XS only),
(version XS only), (version XS
only), (version XS only), (ver-
sion XS only), (version XS only), are
available and by pressing one of them the
desired dose of water can be requested.
The RESET button takes you back to the
previous menu.
Supposing you want to program the but-
ton .
Water
The water dose is programmed in cc.
The buttons ▼ and ▲ allow you to alter
the dose: 1 ÷4000 cc, step 1 cc.
The ENTER button confirms the value and
allows you to proceed to the following
paragraph.
The RESET button allows you to return to
the previous menu. leaving the value of
the parameter as it was before the alteration.
By pressing the button activated (in the
example, button ), a coffee cycle
with parameters associated with the dose
is initiated with the purpose of carrying out
the programming for the simulation of the
dose of water. The infusion will continue
until the STOP or button is pressed,
initiating the final phase of the coffee
cycle. At the end of the cycle, the display
indicates the number of cc’s programmed,
which can however be modified manually
with the ▼ and ▲ buttons.
Extra Water
The extra water dose is programmed
together with the coffee dose.
Buttons ▼ and ▲ allow you to alter the
time for the addition of extra water:
0.0÷20.0 sec, step 0.1 sec.; setting 0.0 the
extra water is disabled.
The ENTER button confirms the value and
you can proceed to the following paragraph.
The RESET button takes you back to the
previous menu: SELECTION OF BUTTON
leaving the value of the parameter as it
was before alteration.
Grinding time
The grinding time for the right and left
grinders can be programmed.
Buttons ▼ and ▲ allow you to alter the
grinding time: 0.1÷30.0 sec., step 0.1 sec.
The ENTER button confirms the value and
you can proceed to the following paragraph.
In case you are at the last parameter
of the dose, the machine returns to the
previous menu: BUTTON SELECTION.
The RESET button takes you back to the
previous menu: BUTTON SELECTION
leaving the value of the parameter as it
was before the alteration.
Dose parameters
In the following table we list the parameters
requested in programming doses for
each type of beverage.
COFFEE SELECTIONS
Parameter Range Step
water dose 1÷4000 cc 1 cc
extra water dose 0.0÷20.0 sec. 0.1 sec.
grind time rt 0.1÷30.0 sec. 0.1 sec.
grind time lt 0.1÷30.0 sec. 0.1 sec.
CAPPUCCINO SELECTIONS
Parameter Range Step
water dose 1÷4000 cc 1 cc
extra water dose 0.0÷20.0 sec. 0.1 sec.
grind time rt 0.1÷30.0 sec. 0.1 sec.
grind time lt 0.1÷30.0 sec. 0.1 sec.
milk time 0.1÷20.0 sec. 0.1 sec.
milk washing time 0.1÷10.0 sec. 0.1 sec.