Flexel® 3D LevMix System for Drum

More documents

Recommendations

Info

5. Superconducting Drive Unit The Superconducting drive unit is sealed for water|spray resistance and has a splash resistant control box. The unit is easily maneuvered for placement under the mixing tank. Figure 3. Location of components of drive unit control box 8
6. Charging the Superconductors Figure 4. Sequence of steps for charging superconductors Procedure Before plugging in the machine, follow the steps below. A. If the drive unit is transported or stored in colder temperatures than the operating environment it is necessary to wait 2 hours to equalize the internal temperatures of the drive unit before turning it on. B. Ensure that the adjustable speed drive toggle switch is in the OFF (down) position and the RPM control knob is turned to zero (0), and remains in this position until charging is complete. C. Remove protective shield from magnetic charger and place magnetic charger with bearing in the receiving cavity on the levitation head. D. Identify the main power button on the control box: Connect the superconducting drive unit to a standard 230 V 50|60 Hz. power source, lift the clear plastic shield over the red main power button, and push the button IN so that it is illuminated. The RPM readout panel will not illuminate until charging is complete (35 minutes), at which time it should read 0 RPM. Ensure that electrical power remains connected to the machine even after charging is complete. To prevent accidental shut-off of the drive unit, keep the clear plastic shroud down to cover the main power button. Do not use alternative spacing|separating devices when charging the drive. Use only the magnetic charger provided in the kit. While drive unit is charging, you can continue with Dolly – Tank Assembly (Section 7). A. After the drive unit has charged for 35 minutes, lift the magnetic charger and replace the protective shield on the magnetic charger. B. Remove the protective shield from the test impeller and place the test impeller on the levitation head. At this point it should levitate freely above the surface of the levitation head. This will indicate that the machine is ready for operation.* C. Test for true rotation of levitated test impeller by moving the switch on the control box to the ON position and turn the RPM Regulator Knob clock-wise and set the arrow at 50. The levitated impeller will spin. The levitation gap must remain uniform (no wobbling of the impeller)*. D. Move the switch on the control box to the OFF position and then remove the test impeller. (Do not try to remove the test impeller while it is spinning.) Replace the protective shield on the test impeller. The unit is now ready to be placed under the mixing tank to begin mixing. ! Always put the protective shield back on the magnetic charger when charging procedure is complete. * If the test impeller does not levitate or substantial wobbling takes place (more than 1mm change in gap) the system must be reset. Turn the system off for 25 minutes and repeat set up procedure. If problem continues, contact a your Sartorius Stedim Biotech representative. 9
Page 1 and 2: Hardware Manual | Hardwareanleitung
Page 3 and 4: ! Safeguards and Precautions Table
Page 5 and 6: 4. Flexel ® 3D LevMix System for D
Page 7: Figure C: Left: Drive- Flexel ® 3D
Page 11 and 12: 8. Flexel ® 3D LevMix Bags for Dru
Page 13 and 14: 10. Coupling the Flexel ® 3D LevMi
Page 15 and 16: 13. Sartorius Stedim Biotech Servic
Page 17 and 18: 1. Technische Daten 2. Überblick 3
Page 19 and 20: Abbildungen und Beschreibungen des
Page 21 and 22: 5. Superleitende Antriebseinheit Di
Page 23 and 24: 7. Rollwagen-|Behältermontage A. D
Page 25 and 26: 9. Einsetzen der Flexel ® 3D LevMi
Page 27 and 28: 11. Mischvorgang 12. Die superleite
Page 29 and 30: ! Consignes de sécurité Table des
Page 31 and 32: 4. Système Flexel ® 3D LevMix pou
Page 33 and 34: Figure C : Gauche : Entraînement-
Page 35 and 36: 6. Chargement des supraconducteurs
Page 37 and 38: 8. Assemblage sacs Flexel ® 3D Lev
Page 39 and 40: 10. Raccordement des sacs Flexel ®
Page 41 and 42: 13. Services Sartorius Stedim Biote
Page 43 and 44: 1. Specifiche 2. Panoramica 3. Prin
Page 45 and 46: Figure e descrizioni degli accessor
Page 47 and 48: 5. Unità motrice superconduttrice
Page 49 and 50: 7. Montaggio carrello - serbatoio A
Page 51 and 52: 9. Inserimento dei sacchetti Flexel
Page 53 and 54: 11. Miscelazione 12. Rimozione dell
Page 55 and 56: ! Salvaguardas y precauciones Tabla
Page 57 and 58: 4. Componentes y accesorios del sis
Page 59 and 60:
Figura C: Izquierda: Interfaz motri
Page 61 and 62:
6. Carga de los superconductores Un
Page 63 and 64:
8. Ensamblaje de la interfaz de las
Page 65 and 66:
10. Acoplamiento de las bolsas ® 3
Page 67 and 68:
13. Servicio Stedim Biotech de Sart
show all

Flexel® 3D LevMix System for Drum

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?