601-0117&0118-02 GP1 Master User Guide.indd
601-0117&0118-02 GP1 Master User Guide.indd
601-0117&0118-02 GP1 Master User Guide.indd
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
INDICATORS english LEUCHTANZEIGEN deutsch INDICATEURS francais INDICADORES<br />
español<br />
INDICATOR LIGHT<br />
The light next to the power key indicates the overall system<br />
status by blue, orange and red colors .<br />
FLASHING BLUE LIGHT<br />
The projector has been turned on, and is warming up .<br />
PERMANENT BLUE LIGHT<br />
The projector is turned on and in normal operation .<br />
PERMANENT ORANGE LIGHT<br />
The unit is in standby mode; no source(s) connected, or the<br />
source(s) connected are inactive or switched off, thereby<br />
activating the powersave function (DPMS) . You may enable<br />
or disable the power save function in the SET UP sub menu,<br />
DPMS on or off .<br />
FLASHING YELLOW LIGHT<br />
Please wait . The yellow light will flash once after power<br />
cord is connected (4 - 5 sec .), and a period after going to<br />
standby mode while lamp is cooling down (approximately<br />
45 sec .) . The projector may not be turned on again until the<br />
light has turned to permanent yellow .<br />
FLASHING RED LIGHT<br />
Projector is overheated . Turn off immediately! Check if<br />
air inlets are covered or if ambient temperature is outside<br />
specifications . The projector can not be restarted unless the<br />
power cord is disconnected and reconnected again . If the<br />
projector continues to flash red, you will need to return the<br />
unit for service .<br />
PERMANENT RED LIGHT<br />
Lamp life has expired . Please change projection lamp<br />
immediately . Failing to change lamp may lead to lamp<br />
explosion .<br />
NO LIGHT<br />
Power is not connected to the projector .<br />
20<br />
LEUCHTANZEIGEN<br />
Die Leuchte neben dem Ein-Aus-Schalter zeigt in blau,<br />
orange bzw . rot den allgemeinen Zustand des Geräts an .<br />
BLINKENDES BLAUES LICHT<br />
PERMANENT BLAUES LICHT<br />
Der Projektor ist angeschaltet und befindet sich im<br />
normalen Betrieb .<br />
PERMANENT ORANGES LICHT<br />
Das Gerät befindet sich im Standby-Betrieb; es sind keine<br />
Quellen angeschlossen oder die angeschlossene Quelle<br />
bzw . Quellen sind nicht aktiv oder ausgeschaltet, so<br />
dass die Stromsparfunktion (DPMS) aktiviert wurde . Die<br />
Stromsparfunktion kann im SETUP-Untermenü DPMS an<br />
oder aus aktiviert bzw . deaktiviert werden .<br />
BLINKENDES GELBES LICHT<br />
Bitte warten . Das gelbe Licht blinkt eine gewisse Zeit<br />
nachdem das Stromkabel angeschlossen wurde (4 - 5<br />
Sek .), sowie eine gewisse Zeit nach dem Umschalten<br />
in den Standby-Betrieb, während die Lampe abkühlt<br />
(ungefähr 45 Sek .) . Der Projektor kann nicht wieder<br />
eingeschaltet werden, solange die Leuchtanzeige nicht<br />
wieder auf permanent gelb gewechselt hat .<br />
BLINKENDES ROTES LICHT<br />
Der Projektor ist überhitzt . Sofort ausschalten! Prüfen<br />
Sie, ob die Belüftungsöffnungen verdeckt sind oder die<br />
Raumtemperatur die vorgegebenen Werte übersteigt . Der<br />
Projektor kann nicht eingeschaltet werden, außer das<br />
Stromkabel wird abgezogen und erneut eingesteckt . Blinkt<br />
der Projektor immer noch rot, so muss er zur Reparatur<br />
gegeben werden .<br />
PERMANENT ROTES LICHT<br />
Die Lebensdauer der Lampe ist abgelaufen . Tauschen Sie<br />
die Projektorlampe bitte umgehend aus . Wird die Lampe<br />
nicht ausgetauscht, kann dies zu einer Explosion der<br />
Lampe führen .<br />
KEIN LICHT<br />
Die Stromversorgung des Projektors ist nicht hergestellt .<br />
INDICATEUR<br />
Le voyant lumineux à coté de la touche power indique<br />
l’état général du système par des couleurs bleu, orange<br />
et rouge .<br />
LUMIERE BLEUE CLIGNOTANTE<br />
LUMIERE BLEUE PERMANENTE<br />
Le projecteur est allumé et fonctionne normalement .<br />
LUMIERE ORANGE PERMANENTE<br />
L’appareil est en mode veille ; il n’y a pas de source<br />
connectée, ou la source connectée est inactive ou éteinte,<br />
activant ainsi la fonction économie d’énergie (DPMS) .<br />
Vous pouvez activer ou désactiver la fonction économie<br />
d’énergie dans le sous-menu SET UP, DPMS sur ON ou<br />
OFF .<br />
LUMIERE JAUNE CLIGNOTANTE<br />
Veuillez patienter . La lumière jaune clignote pendant<br />
quelques secondes après avoir connecté le cordon<br />
d’alimentation (4 - 5 sec), et après la mise en veille tant<br />
que la lampe refroidi (approximativement 45 sec .) . Le<br />
projecteur ne peut pas être rallumé tant que la lumière<br />
jaune n’est pas permanente .<br />
LUMIERE ROUGE CLIGNOTANTE<br />
Le projecteur est en surchauffe . Eteignez immédiatement<br />
Vérifiez si les arrivées d’air ne sont pas bouchées ou si la<br />
température ambiante est au-delà des caractéristiques .<br />
Le projecteur ne peut être redémarré que si le cordon<br />
d’alimentation est débranché puis rebranché . Si le<br />
projecteur continu de clignoter rouge, vous devez<br />
retourner l’appareil au service après-vente .<br />
LUMIERE PERMANENTE ROUGE<br />
La durée de vie de la lampe est dépassée . Veuillez<br />
changer la lampe de projection immédiatement . Ne pas<br />
changer la lampe peut entraîner l’explosion de la lampe .<br />
PAS DE LUMIERE<br />
Le projecteur n’est pas alimenté .<br />
INDICADOR<br />
La luz junto a la tecla de encendido indica el estado general<br />
del sistema mediante los colores azul, naranja y rojo .<br />
LUZ AZUL INTERMITENTE<br />
LUZ AZUL PERMANENTE<br />
El proyector está encendido y funciona con normalidad .<br />
LUZ NARANJA PERMANENTE<br />
El aparato está en modo de espera; no hay ninguna fuente<br />
conectada, o si la hay está inactiva o apagada y, por<br />
tanto, se activa la función de ahorro de energía (DPMS) .<br />
Puede activar o desactivar la función de ahorro de energía<br />
en el submenú INSTALACIÓN, seleccionando DPMS On<br />
(activado) u Off (desactivado) .<br />
LUZ AMARILLA INTERMITENTE<br />
Por favor, espere . La luz amarilla parpadeará durante 4<br />
o 5 segundos tras conectarse el cable de alimentación<br />
y durante 45 segundos, aproximadamente, después de<br />
entrar en modo de espera mientras la lámpara se enfría . No<br />
se puede encender el proyector de nuevo hasta que la luz<br />
amarilla se quede fija .<br />
LUZ ROJA INTERMITENTE<br />
El proyector se ha sobrecalentado . ¡Apáguelo<br />
inmediatamente! Compruebe si las entradas de aire<br />
están tapadas o si la temperatura ambiente supera la<br />
especificada . El proyector no puede encenderse de nuevo<br />
si no se desenchufa y se vuelve a enchufar el cable de<br />
alimentación . Si la luz roja del proyector sigue parpadeando,<br />
tendrá que llevar el aparato para que lo reparen .<br />
LUZ ROJA FIJA<br />
La vida útil de la lámpara ha concluido . Cambie la lámpara<br />
de proyección inmediatamente . Si no se cambia la lámpara,<br />
podría estallar .<br />
NO HAY LUZ<br />
La alimentación no está conectada al proyector .