Costruire casse acustiche

Optima
Per gli ordini fare attenzione alle unità di confezione dei componenti contrassegnati con +.
L’elenco del materiale è sempre riferito ad una sola cassa.
Trasduttore
Woofer midrange .............1 SPH-165CP
Tweeter ............................1 DT-254
Filtri
Circuito stampato.............1 DNU-300
L1.....................................1 LSIP-100/1
L2.....................................1 LSIP-47/1
L3.....................................1 LSIP-47/1
C1....................................1 LSC-68, LSC-68R +
C2....................................1 LSC-330NP +
C3....................................1 LSCP-68R +
C4....................................1 LSC-220, LSC-220R +
R1 ....................................1 LSR-82/10
R2 ....................................1 LSR-56/20
R3 ....................................1 LSR-47/20
Accessori
Morsetto ..........................1 ST-960GM
Tubi BR.............................1 BR-70HP
Insonorizzazione...............2 Matten MDM-3
Cavo .............................2m SPC-215 +
Viti ...................................8 MZF-8615 (Unità conf.=16)
4 MZF-8614 (Unità conf.=16)
Legno 19mm MDF
Lati...................................2 212 x650mm
Fondo+coperchio.............2 212 x162mm
Frontale............................1 650 x200mm
Retro ................................1 1025*x200mm
Rinforzi.............................1 212x50mm
1 162x50mm
Elemento F .......................1 piede a scelta
*= lunghezza adattabile a (elemento F + 650mm)!
!in alternativa, OPTIMA può essere
costruita anche con l’SPH-165C.
I bassi saranno allora più voluminosi.
Tuttavia si ridurranno la stabilità dei
livelli e l’efficienza.
Per il filtro basta adattare R2 e R3
(vedi schema elettrico).
As an alternative, the OPTIMA can
also be equipped with the SPH-165C.
Then the bass range is even more
voluminous. However, the level
stability and the efficiency are reduced.
Concerning the crossover network,
only R2 and R3 have to be matched
(see circuit diagram of crossover
network).
Optima
When ordering, please consider the packing units
of the components which are marked with +.
The quantity of material always refers to one cabinet.
Speaker Concept No. 30
Speakers
Bass-midrange speaker .....1 SPH-165CP
Tweeter ............................1 DT-254
Crossover network
PCB ..................................1 DNU-300
L1.....................................1 LSIP-100/1
L2.....................................1 LSIP-47/1
L3.....................................1 LSIP-47/1
C1 ....................................1 LSC-68, LSC-68R +
C2 ....................................1 LSC-330NP +
C3 ....................................1 LSCP-68R +
C4 ....................................1 LSC-220, LSC-220R +
R1 ....................................1 LSR-82/10
R2 ....................................1 LSR-56/20
R3 ....................................1 LSR-47/20
Accessories
Morsetto ..........................1 ST-960GM
Bass reflex tubes...............1 BR-70HP
Dampening ......................2 pads MDM-3
Cable ............................2m SPC-215 +
Screws..............................8 MZF-8615 (packing unit=16)
4 MZF-8614 (packing unit=16)
Wood 19mm MDF
Side walls .........................2 212 x 650mm
Bottom plate+cover .........2 212 x162mm
Front ................................1 650 x 200mm
Rear wall ..........................1 1025*x200mm
Bracings ...........................1 212x50mm
1 162x50mm
Element F .........................1 foot element acc. to selection
*= can be matched in length (element F + 650mm)!
MONACOR ® International 53