TECHNICAL MANUAL - Tyrolia

More documents

Recommendations

Info

NOTE - only for CARVE PLATE 13 and CARVE PLATE 9: If you want to mount rental bindings on CARVE PLATE 13 or CARVE PLATE 9 use template SP 2003 W for SP models and Template SR 2003 W for SR models. When mounting a RENTAL binding on the CARVE PLATE using template BASES & PLATES for installation then you have to displace the template to the rear according to the following table. Binding SP 130 ABS DEMO AERO SP 120 ABS DEMO SP 100 ABS SR 100 SP 90 ABS SP 75 ABS 4.2 MOUNTING - BINDINGS ON PLATES Determine the boot sole length with the HEAD/TYROLIA Rental boot caliper and place the binding on the Carve Plate corresponding with the appropriate printed length markings. pict 25 Mount the binding in accordance with the procedures in this manual. pict 26 NOTE: MOUNTING HEAD/TYROLIA BINDINGS ON RAISED PLATFORMS: • Replacing the POWER BRAKE is not necessary when you mount HEAD/TYROLIA bindings with the HEAD/TYROLIA SPEEDPLATE PLUS 13, POWER PLATE 9, CARVE PLATE 13 SLR or CARVE PLATE 9 SLR on skis which do not have integrated platforms. • The HEAD/TYROLIA DRAGON BRAKE has extended brake arms and increased braking power. Unscrew and remove both front heel screws and pull the POWER BRAKE off the heel (see pict 27). 26 / MOUNTING Displacement of the boot midpoint indicator to the rear, for template 92 W. 10 mm 20 mm 30 mm pict 27 • Then slide on the DRAGON BRAKE (see pict 28) and screw it on. pict 28 CAUTION: If you use HEAD/TYROLIA bindings on plates from other manufacturers, check the HEAD/TYROLIA Brake Matrix to see if the desired combination of ski-plate-binding is possible. FOLLOW THE PROCEDURE BELOW: 1. Add the weight of the components you want to mount (ski + plate + binding). 2. Add the thickness of the components you want to mount (ski + plate + binding). 3. Using the list below, determine which HEAD/TYROLIA brakes are standard on the bindings delivered. 4. Find the value on the vertical axis which corresponds to the sum of the addition for the stand height. 5. Follow the horizontal axis on the matrix to the right until you find the value which corresponds to the total weight on the horizontal axis. 6. If the point of intersection of the weight and stand height lies below the respective curve, the brake will function properly. 7. If the point of intersection lies above the curve for the POWER BRAKE, the brake must be replaced with the next stronger one. 8. If the point of intersection lies above the curve for the DRAGON BRAKE, using this combination of ski + binding + plate is not recommended. In this case, you have the following possibilities to come within the permitted range: a) Reduce the total thickness through: – a thinner plate, – a HEAD/TYROLIA binding with less stand height (see page 14-17). b) Reduce the total weight to – a lighter plate, e. g. a HEAD/TYROLIA CARVE PLATE 9 SLR – a HEAD/TYROLIA binding with less weight, – a lighter ski. c) Use a combination of a) + b).
80 HEAD/tyrolia BRAKE MATRIX LINE 08.09 75 70 65 60 55 Total Stand Height in mm 50 45 40 2500 2600 2700 2800 2900 3000 3100 3200 3300 3400 3500 3600 3700 3800 3900 4000 4100 4200 4300 4400 Total Weight in gram PB RACE PRO WIDE 115 PB RACE PRO XFAT 130 PB LD XFAT 130 PB LD FAT 115 PB LD RAIL FAT 115 PB RACE PRO 16-78 PB RACE PRO 17-78 PB LD 78 PB LD RAIL 80 PB LD WIDE 85 PB RACE PRO FAT WIDE 97 PB LD WIDE 97 PB LD RAIL WIDE 97 DRAGON BRAKE 78 SL JUNIOR BRAKE 72-05 SL JUNIOR BRAKE WIDE 90 SL JUNIOR BRAKE RAIL 78 SL BRAKE 78-04 SL BRAKE WIDE 90 SL BRAKE SPEEDRAIL 78 SL BRAKE SPEEDRAIL WIDE 90 MOUNTING / 27
Page 1 and 2: ALPINE SKIBINDINGS 08.09 TECHNICAL
Page 3 and 4: Ski bindings 08.09 Reliability, Qua
Page 5 and 6: HIGH TECH & HIGH QUALITY ABS - ANTI
Page 7 and 8: SPEEDRAIL SYSTEM Easier, faster, sa
Page 9 and 10: DIAGONAL HEEL The Light Diagonal He
Page 11 and 12: TEMPLATES TEMPLATES / 9
Page 13 and 14: tyrolia line 08.09 SL 45 EARLIER LI
Page 15 and 16: etail bindings RETAIL BINDINGS / 13
Page 17 and 18: datasheet Heel stand height Heel ty
Page 19 and 20: datasheet Heel stand height Heel ty
Page 21 and 22: DRILL TEMPLATE 92 W 1. Compatibilit
Page 23 and 24: FOR SL 110 CARVE ABS: Connect the C
Page 25 and 26: DRILL TEMPLATE 94 W 1. Compatibilit
Page 27: DRILL TEMPLATE BASES & PLATES 1. Co
Page 31 and 32: TYROLIA BINDING-PLATE COORDINATION
Page 33 and 34: 5. RAILFLEX SYSTEM II & RAILFLEX LI
Page 35 and 36: pict 40 Slide the binding on the RA
Page 37 and 38: 5.3 BOOT CENTER ADJUSTMENT Dependin
Page 39 and 40: Then you can place the front and th
Page 41 and 42: RENTAL BINDINGS RENTAL BINDINGS / 3
Page 43 and 44: datasheet Brake type Ramp angle (mm
Page 45 and 46: DRILL TEMPLATE SP 2003 W 4 5 1. Com
Page 47 and 48: DRILL TEMPLATE SR 2003 W 4 5 1. COM
Page 49 and 50: SYMPRO-SYMRENT-SYSTEM 08.09 Perform
Page 51 and 52: SYMPRO-SYMRENT-BYS ON THE SHOP FLOO
Page 53 and 54: Color Code Bar Code Holder Red Colo
Page 55 and 56: BOOT-HANDLING AND TESTING VISUAL IN
Page 57 and 58: BRAKES SPARE PARTS MAINTENANCE & SE
Page 59 and 60: Ski width Art. No. Brake Picture Mo
Page 61 and 62: Ski width Art. No. Brake Picture Mo
Page 63 and 64: TYROLIA SCREW OVERVIEW - 08.09 Mode
Page 65 and 66: MAINTENANCE & SERVICE VISUAL INSPEC
Page 67 and 68: RACING (X)-BINDINGS Certain binding
Page 69 and 70: TROUBLESHOOTING (INCLUDING RENTAL)
Page 71 and 72: ADJUSTMENT TEMPLATES ADJUSTMENT & T
Page 73 and 74: RELEASE/RETENTION ADJUSTMENT TABLE
Page 75 and 76: TROUBLE SHOOTING RELEASE/RETENTION
Page 77 and 78: • Remind skiers to clean their bo
Page 79 and 80:
RETAILER AGREEMENTS AND INDEMNIFICA
Page 81 and 82:
RISK MANAGEMENT Indemnification, In
Page 83 and 84:
USE OF NON-RECOMMENDED SETTINGS SKI
Page 85 and 86:
Shop Name Phone Address City State,
Page 87 and 88:
ONLINE DEALER SUPPORT www.tyrolia.c
Page 89 and 90:
NOTES / 87
Page 91 and 92:
Release/retention - adjustment Tabl
Page 93 and 94:
DRILL TEMPLATE CHART 2008/09 HEAD F
show all

TECHNICAL MANUAL - Tyrolia

Create successful ePaper yourself

Delete template?

Save as template?