mOUNTING OF JUNIOR BINDINGS ON CARVE PLATES OR ON SKIS ≥ 140 CM For mounting the SL 75, MOJO 7.5, SL 70 AC, SL 90 ABS JR RACE and SP 75 ABS on CARVE Plates or on skis, 140 cm and longer, replace the premounted screws by 8 mm penetration depth screws. Only with these screws can we guarantee the right pullout strength (see table). SL 75 SL 70 AC SL 90 ABS JR Race SP 75 ABS 30 / MOUNTING MOJO 7.5 162 639 5,5 x 9,0 162 401 162 401 162 376 162 376 162 488 5,5 x 19,5 5,5 x 15,5 162 639 162 639 5,5 x 9,0 5,5 x 9,0 5,5 x 15,5 162 401 5,5 x 15,5 162 383 162 426 5,5 x 21,5 5,5 x 16,9 5,5 x 13,4 162 639 5,5 x 9,0 5,5 x 13,4 162 376 5,5 x 13,4 162 416 5,5 x 19,4 160 018 160 018 5,5 x 18,5 160 018 5,5 x 18,5 5,5 x 18,5 160 018 5,5 x 18,5 160 018 5,5 x 18,5 162 458 162 458 5,5 x 29,0 5,5 x 29,0 160 031 160 031 5,5 x 20,5 5,5 x 20,5 160 031 162 423 5,5 x 21,5 5,5 x 20,5 160 031 5,5 x 20,5 162 461 162 461 5,5 x 32,5 5,5 x 32,5
5. RAILFLEX SYSTEM II & RAILFLEX LITE HEAD RAILFLEX BASE II RFD 14 RFD 14 DEMO RFD 12 RFD 11 DEMO RF 1 1 ONE RF 9 TYROLIA RAILFLEX BASE II RFD 12 RFD 1 1 RF 10 RAILFLEX SYSTEM II - SPEEDRAIL All RAILFLEX System II bindings are equipped with the SPEEDRAIL band. With this band it is possible to adjust the binding to the boot sole length directly on the ski, and do so without any screws. You can use this system also for DEMO purposes, but for on snow demos we still recommend the RAILFLEX DEMO bindings. The SPEEDRAIL band is for boot sole lengths from 260- 360 mm. For longer boot soles we still offer the longer RAILFLEX band as a spare part. This band is for boot soles from 290-390 mm, but doesn’t offer the feature BOOT CENTER ADJUSTMENT (+15 / 0/ -15). RAILFLEX LITE SYSTEM HEAD/TYROLIA offers two versions of the RAILFLEX LITE band. The appropriate band is delivered with the integrated HEAD ski or the RAILFLEX LITE base. Band version short long Spare part number 162757 162758 Ski length (Recommendation) RAILFLEX LITE RFL 7.5 RFL 4.5 RAILFLEX LITE RFL 9 RFL 4.5 under 127cm 127cm and longer Boot sole length 220-300 mm 240-325 mm Mondo size ~ 17.0-25.5 ~ 19.5-27.5 NOTE: For skis under 140 cm we are offering the RAILFLEX LITE BASE with short screws (penetration depth: 6 mm) and for skis of 140 cm and longer with long screws (penetration depth: 8 mm). Choose the right screw length according to the ski length (see screw chart on page 60-61). HEAD/TYROLIA offers different types of brakes for RAILFLEX bindings. Refer to the brake overview on page 56-59 for brake and binding compatibility. 5.1 MOUNTING - BASES The mounting of both RAILFLEX Base and RAILFLEX LITE Base is similar to the plates. Just select the right mounting mark and the appropriate bushings - black for RAILFLEX LITE and white for RAILFLEX. For more details see page 25. RAILFLEX BASE Place the front section of the RAILFLEX Base over the holes and tighten the screws. Then place the rear section over the holes and tighten the screws as well (pict 29). pict 29 Finally cover the RAILFLEX BASE with the appropriate covers (pict 30). pict 30 RAILFLEX LITE BASE Place the front section of the RAILFLEX LITE Base over the holes and tighten the screws. Repeat the same procedure with the rear section of the base (pict 31). pict 3 1 5.2 MOUNTING - BINDINGS RAILFLEX SYSTEM II - SPEEDRAIL Make sure that the boot is satisfying the international standards and has no functional damage. Take the binding parts out of the box and follow the steps on the instruction leaflet. Determine the boot sole length with the HEAD/ TYROLIA rental caliper (art. no. 162 61 7). pict 32 MOUNTING / 31