13. ROHRLEITUNGSPLANUNG 13.1 Druckverluste Verschiedene Widerstände in den Rohrleitungen führen zu progressiven Wasser- oder Gasdruckverluste. Widerstände ergeben sich sowohl von Rohrreibungen in geraden Leitungen als auch von einzelnen Formstücke wie Richtungsänd erungen, Querschnittreduzierungen usw. Der gesamte Druckverlust in den Rohrleitungen wird wie folgt kalkuliert: wobei: Δp= Δp1 + Δp2 - Δp1 Druckverlust gerade Leitungen - Δp2 Druckverlust von einzeln lokalisierten Widerstände 13.2 Druckverlustfestlegung - gerade Leitungen Druckverlust mit gerade Rohrleitungen wird wie folgt kalkuliert: wobei: Δp1 = ΣR • l - R Druckverlustwert in bar / m oder Pa/m - l Gerader Leitungsteil in m Einzeldruckverluste werden jeweils wie folgt zusmmmengelegt: dove: R = λ • ρ • v 2 /2 • d - λ Leitung Reibungsfaktor - ρ Flüssigkeitsdichte in kg/dm 3 - v Fliessgeschwindigkeit in m/s - d Rohrleitungsdurchmesser in mm Druckverlust praktische Methode > siehe folgende Tafeln. Bedienungsanleitung 24 Technical Guide 13. PIPE CALCULATION 13.1 Pressure drops PRESSFITTING SYSTEM Water or gas, which ow in the pipes, gradually lose their own pressure, because of the dierent resistances they meet on the course. These resistances are due both to straight pipe resistance or to single casual conditions as direction changes, section reductions, etc. Therefore the whole of pressure drops for a pipe system is calculated according to the following formula: where: Δp= Δp1 + Δp2 - Δp1 is the pressure drop due to straight lengths - Δp2 is the pressure drop due to single localized resistances 13.2 Pressure drops of a straight pipe The following formula is used to calculate pressure drops, due to straights lenghts where Δp1 =ΣR • l - R is the unitary pressure drop expressed in mbar o in Pa/m - l is the straight pipe length in m As well, the following formula is used to calculate the unitary pressure drop: where: R = λ • ρ • v 2 /2 • d - λ is the pipe friction coef cient - ρ is the uid density expressed in kg/m 3 - v is the uid speed expressed in m/s - d is the internal pipe diameter in mm For a practical calculation of pressure drops it is possible to refer to the following tables.
PRESSFITTING SYSTEM <strong>Edelstahl</strong>rohre für Trinkwasseranwendungen (Rauhigkeit k= 0,0015 mm). Druckverluste R abhängig vom Vp Höechstmenge v Geschwindigkeit bei 10 °C Temperatur Abmessung Rohraussen Ø x Wandstärke Abmessung Rohraussen Ø x Wandstärke Abmessung Rohraussen Ø x Wandstärke Nominal size Pipe outside diameter x wall thickness Nominal size Pipe outside diameter x wall thickness Nominal size Pipe outside diameter x wall thickness AD x s / OD x t [mm] 15 x 1.0 18 x 1.0 22 x 1.2 28 x 1.2 AD x s / OD x t [mm] 35 x 1.5 42 x 1.5 54 x 1.5 AD x s / OD x t [mm] 76,1 x 2,0 88,9 x 2,0 108 x 2,0 di / ID [mm] 13.0 16.0 19.5 25.6 di / ID [mm] 32 39 51 di / ID [mm] 72.1 84.9 104 Spitzen-durch usse Spitzen-durch usse Spitzen-durch usse Peak ow rate Peak ow rate Peak ow rate Vp R v R v R v R v Vp R v R v R v Vp R v R v R v Tab. 1 I mbar m mbar m mbar m mbar m I mbar m mbar m mbar m I mbar m mbar m mbar m s m s m s m s m s s m s m s m s s m s m s m s 0,05 2,2 0,4 0,8 0,2 0,3 0,2 0,1 0,1 0,2 0,3 0,2 0,1 0,2 0 0,1 1 0,1 0,2 0,1 0,2 0 0,1 0,1 7,3 0,8 2,7 0,5 1,1 0,3 0,3 0,2 0,4 1,1 0,5 0,4 0,3 0,1 0,2 2 0,4 0,5 0,2 0,4 0,1 0,2 0,15 14,8 1,1 5,5 0,7 2,1 0,5 0,6 0,3 0,6 2,3 0,7 0,9 0,5 0,3 0,3 3 0,8 0,7 0,4 0,5 0,1 0,4 0,2 24,5 1,5 9,1 1 3,5 0,7 1 0,4 0,8 3,8 1 1,5 0,7 0,4 0,4 4 1,4 1 0,6 0,7 0,2 0,5 0,25 36,2 1,9 13,5 1,2 5,1 0,8 1,4 0,5 1 5,7 1,2 2,2 0,8 0,6 0,5 5 2 1,2 0,9 0,9 0,4 0,6 0,3 50 2,3 18,6 1,5 7,1 1 2 0,6 1,2 7,9 1,5 3,1 1 0,8 0,6 6 2,8 1,5 1,3 1,1 0,5 0,7 0,35 65,6 2,6 24,3 1,7 9,3 1,2 2,6 0,7 1,4 10,3 1,7 4 1,2 1,1 0,7 7 3,7 1,7 1,7 1,2 0,6 0,8 0,4 83,2 3 30,8 2 11,7 1,3 3,3 0,8 1,6 13,1 2 5,1 1,3 1,4 0,8 8 4,7 2 2,2 1,4 0,8 0,9 0,45 102,5 3,4 38 2,2 14,4 1,5 4 0,9 1,8 16,2 2,2 6,3 1,5 1,7 0,9 9 5,9 2,2 2,7 1,6 1 1,1 0,5 123,7 3,8 45,7 2,5 17,3 1,7 4,9 1 2 19,5 2,5 7,6 1,7 2,1 1 10 7,1 2,5 3,2 1,8 1,2 1,2 0,55 146,6 4,1 54,2 2,7 20,5 1,8 5,7 1,1 2,2 23,1 2,7 9 1,8 2,5 1,1 11 8,4 2,7 3,8 1,9 1,4 1,3 0,6 171,3 4,5 63,2 3 23,9 2 6,7 1,2 2,4 27,1 3 10,5 2 2,9 1,2 12 9,9 2,9 4,5 2,1 1,7 1,4 0,65 197,5 4,9 72,9 3,3 27,6 2,2 7,7 1,3 2,6 31,2 3,2 12,1 2,2 3,3 1,3 13 11,4 3,2 5,2 2,3 2 1,5 0,7 225,5 5,3 83,2 3,5 31,5 2,3 8,8 1,4 2,8 35,7 3,5 13,8 2,3 3,8 1,4 14 13 3,4 5,9 2,5 2,2 1,7 0, 7 5 94,2 3,8 35,6 2,5 10 1,5 3 40,4 3,7 15,6 2,5 4,3 1,5 15 14,8 3,7 6,7 2,7 2,5 1,8 0, 8 105,6 4 39,9 2,7 11,1 1,6 3,2 45,4 4 17,5 2,7 4,8 1,6 16 16,5 3,9 7,5 2,8 2,8 1,9 0, 8 5 117,8 4,3 44,5 2,9 12,4 1,7 3,4 50,6 4,2 19,5 2,9 5,4 1,7 17 18,5 4,2 8,4 3 3,2 2 0, 9 130,4 4,5 49,2 3 13,7 1,8 3,6 56,1 4,5 21,7 3 6 1,8 18 20,6 4,4 9,3 3,2 3,5 2,1 0, 9 5 143,7 4,8 54,2 3,2 15,1 1,9 3,8 61,9 4,7 23,9 3,2 6,6 1,9 19 22,7 4,7 10,3 3,4 3,9 2,2 1 157,6 5 59,4 3,3 16,5 1,9 4 67,9 5 26,2 3,4 7,2 2 20 24,9 4,9 11,3 3,5 4,3 2,4 1, 0 5 64,8 3,5 18 2,1 4,2 74,1 5,2 28,6 3,5 7,9 2,1 21 27,2 5,1 12,4 3,7 4,6 2,5 1, 1 7,4 3,7 19,6 2,1 4, 4 31,1 3,7 8,6 2, 2 22 13,4 3,9 5,1 2,6 1, 1 5 76,3 3,8 21,2 2,3 4, 6 33,7 3,9 9,3 2, 3 23 14,6 4,1 5,5 2,7 1, 2 82,3 4 22,9 2,3 4, 8 36,3 4 10 2, 4 24 15,7 4,2 5,9 2,8 1, 2 5 88,6 4,2 23,9 2, 4 5 39,1 4,2 10,8 2, 5 25 17 4,4 6,4 3 1, 3 95 4,3 26,4 2,5 5, 2 42,1 4,4 11,6 2, 6 26 18,2 4,6 6,8 3,1 1, 3 5 101,7 4,5 28,2 2,6 5, 4 45 4,5 12,4 2, 7 27 19,6 4,8 7,3 3,2 1, 4 108,6 4,6 30,1 2,7 5, 6 48 4,7 13,2 2, 7 28 20,9 5 7,8 3,3 1, 4 5 115,6 4,8 32 2,8 5, 8 51,1 4,9 14,1 2, 8 29 22,2 5,1 8,4 3,4 1, 5 122,9 5 34 2, 9 6 54,4 5 14,9 2, 9 30 8,9 3,5 1, 5 5 36,1 3 6, 2 15, 9 3 31 9,5 3,7 1, 6 38,2 3,1 6, 4 16,9 3, 1 32 10 3,8 1, 6 5 40,4 3,2 6, 6 17,8 3, 2 33 10,6 3,9 1, 7 42,6 3,3 6, 8 18,7 3, 3 34 11,1 4 1, 7 5 44,9 3, 4 7 19,7 3, 4 35 12,3 4,2 1, 8 47,2 3,5 7, 2 20,7 3, 5 36 12,9 4,3 1, 8 5 49,6 3,6 7, 4 21,8 3, 6 37 13,6 4,4 1, 9 52 3,7 7, 6 22,9 3, 7 38 14,3 4,6 1, 9 5 54,5 3,8 7, 8 24 3, 8 39 15 4,7 2 57 3, 9 8 25,1 3, 9 40 15,7 4,8 2, 0 5 59,6 4 8, 2 26, 3 4 41 16,4 4,9 2, 1 62,2 4,1 8, 4 27,4 4, 1 42 17,1 5 2, 1 5 64,3 4,2 8, 6 28,6 4, 2 43 17,9 5,2 2, 2 67,7 4,3 8, 8 29,9 4,3 44 2, 2 5 70,5 4, 4 9 31,1 4,4 45 2, 3 73,3 4,5 9, 2 32,4 4,5 46 2, 3 5 82,8 4,8 9, 4 33,7 4,6 47 2, 4 86 4,9 9, 6 35 4,7 48 2, 4 5 89,2 5 9, 8 36,3 4,8 49 2, 5 92,5 5, 1 10 37,6 4,9 50 Bedienungsanleitung 25 Technical Guide Stainlesssteel pipes for drinkable water (roughnessk= 0,0015 mm). Pressure drops R as a function of peak ow rateVp and speed v at 10 °C temperature.