Switch Motor - Viessmann Modellspielwaren GmbH
Switch Motor - Viessmann Modellspielwaren GmbH
Switch Motor - Viessmann Modellspielwaren GmbH
Sie wollen auch ein ePaper? Erhöhen Sie die Reichweite Ihrer Titel.
YUMPU macht aus Druck-PDFs automatisch weboptimierte ePaper, die Google liebt.
10<br />
Tillig H0 Elite<br />
Hebel: 8 und 11<br />
Montage: oberflur, neben Gleis<br />
1. Montieren Sie die Hebel gemäß Abbildung 10.1 im<br />
Weichenantrieb und verschließen Sie anschließend<br />
das Gehäuse wieder.<br />
2. Entfernen Sie den markierten Befestigungsring an der<br />
Einkerbung mit einem scharfen Messer.<br />
3. Bringen Sie die Weiche in die zum Antrieb passende<br />
Stellung (Der Hebel des Weichenantriebs muss in den<br />
Hebel der Weiche greifen).<br />
4. Montieren Sie den Antrieb neben der Weiche (Abb.<br />
10.2) und fixieren Sie ihn mit den passenden Distanzhülsen<br />
und Schrauben 2 x Nr. 13.<br />
Abb. 10<br />
10.1 10.2 10.3<br />
Märklin K-Gleis<br />
Hebel: 8 und 10<br />
Montage: oberflur, neben Gleis<br />
1. Montieren Sie die Hebel gemäß Abbildung 11.1 im<br />
Weichenantrieb und verschließen Sie anschließend<br />
das Gehäuse wieder.<br />
2. Entfernen Sie den markierten Befestigungsring an der<br />
Einkerbung mit einem scharfen Messer.<br />
3. Bringen Sie die Weiche in die zum Antrieb passende<br />
Stellung (Der Hebel des Weichenantriebs muss in den<br />
Hebel der Weiche greifen).<br />
4. Montieren Sie den Antrieb neben der Weiche (Abb.<br />
11.2) und fixieren Sie ihn mit den passenden Distanzhülsen<br />
und Schrauben 2 x Nr. 13.<br />
Abb. 11<br />
11.1 11.2 11.3<br />
Tillig H0 Elite<br />
Lever: 8 and 11<br />
Mounting: Overground, beside the track<br />
1. Mount levers 8 and 11 as shown in figure 10.1 into the<br />
switch motor. After mounting the lever, close the casing<br />
with the cover.<br />
2. Cut off the fastening ring at the notch with a sharp<br />
knife as shown in figure 10.1.<br />
3. Bring the turnout into the corresponding position of the<br />
switch motor (the lever of the switch motor has to get<br />
connected with the lever of the turnout).<br />
4. Mount the switch motor beside the turnout as shown<br />
in figure 10.2. Fix the switch motor with the screws 2 x<br />
nr. 13. Use the distance rolls!<br />
Fig. 10<br />
Märklin K-track<br />
Lever: 8 and 10<br />
Mounting: Overground, beside the track<br />
1. Mount the levers 8 and 10 as shown in figure 11.1 into<br />
the switch motor. After mounting the lever, close the<br />
casing with the cover.<br />
2. Cut off the fastening ring at the notch with a sharp<br />
knife as shown in figure 11.1.<br />
3. Bring the turnout into the corresponding position of the<br />
switch motor (the lever of the switch motor has to get<br />
connected with the lever of the turnout).<br />
4. Mount the switch motor beside the turnout as shown<br />
in figure 11.2. Fix the switch motor with the screws 2 x<br />
nr. 13. Use the distance rolls!<br />
Fig. 11