CNC 8037 - Installation manual - Fagor Automation

More documents

Recommendations

Info

1. CNC CONFIGURATION CNC structure CNC 8037 SOFT: V01.4X ·42· "USB" port - USB hard disk (Pen Drive) connection. Installation manual The USB 1.1 port with type A connector admits connecting a "Pendrive" type memory device. These memory devices are commercially available (off-the-shelf) and they're all valid regardless of their size, brand name or model. USB 1.1 port The CNC recognizes the connected device as USB Hard Disk. When it is connected, it will be shown as on the left panel of the . To see its contents, press the (refresh) softkey. Within the USB device, the CNC will only recognize files with extensions *.f55 (software version), *fhw (Firmware updating files), part-programs parameters, tables, screens and symbols. The CNC will not recognize any other type of file. Part-programs cannot be edited or executed from the USB hard disk. (A) USB device The USB extension cable must be used to prevent undesired short-circuits with the metallic housing (A) of the USB device at the CNC. The extension cable must not be longer than 3 m and must be plugged in while the CNC is off. We recommend to use the extension set supplied by Fagor. Once this cable has been plugged in, USB devices may be connected or disconnected through it while the CNC is on. Do not connect a multi-hub USB adapter to connect several devices at the same time. It will only recognize the first Pen Drive that is connected. Nor will it recognize other types of devices such as keyboards, mice, recorders, etc.
Installation manual Connecting the USB extension set supplied by Fagor: 1. Connect the cable and the USB adaptor. Check that the seal and the nut of the USB adaptor are secured as shown in the figure. USB extension cable. Securing nut. USB adapter. 2. While the CNC is off, connect the extension cable to the USB connector of the CNC. OUT IN X7 X9 X2 X10 X3 X11 X4 X12 X5 X1 X8 +24V 0V X13 X6 USB extension cable. 3. Once the extension set has been properly connected, it will be possible to connect and disconnect USB devices to the CNC while it is on. Seal. USB adapter. To connect USB devices. 1. CNC CONFIGURATION CNC structure CNC 8037 SOFT: V01.4X ·43·
Page 1 and 2: CNC 8037 Installation manual Ref.12
Page 3 and 4: Installation manual INDEX About the
Page 5 and 6: Installation manual CHAPTER 9 PLC P
Page 7 and 8: ABOUT THE PRODUCT BASIC CHARACTERIS
Page 9: DECLARATION OF CONFORMITY The manuf
Page 12 and 13: CNC 8037 ·12· Version history
Page 14 and 15: CNC 8037 ·14· Safety conditions P
Page 16 and 17: CNC 8037 ·16· Safety conditions S
Page 18 and 19: CNC 8037 ·18· Warranty terms WARR
Page 20 and 21: CNC 8037 ·20· Material returning
Page 22 and 23: CNC 8037 ·22· Additional remarks
Page 24 and 25: CNC 8037 ·24· Fagor documentation
Page 26 and 27: 1. CNC CONFIGURATION CNC structure
Page 52 and 53: � � � Installation manual 2.
Page 54 and 55: � � � Installation manual 2.
Page 56 and 57: 3. REMOTE MODULES (BUS CAN WITH CAN
Page 72 and 73: 4. MACHINE AND POWER CONNECTION CNC
Page 74 and 75: 4. MACHINE AND POWER CONNECTION Dig
Page 76 and 77: 4. MACHINE AND POWER CONNECTION Set
Page 78 and 79: 4. MACHINE AND POWER CONNECTION Set
Page 80 and 81: 4. MACHINE AND POWER CONNECTION CNC
Page 82 and 83: 4. MACHINE AND POWER CONNECTION Con
Page 84 and 85: 5. MACHINE PARAMETERS CNC 8037 SOFT
Page 90 and 91: 5. MACHINE PARAMETERS CNC 8037 ·90
Page 92 and 93:
5. MACHINE PARAMETERS CNC 8037 ·92
Page 94 and 95:
Page 96 and 97:
5. MACHINE PARAMETERS CNC 8037 SOFT
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
5. MACHINE PARAMETERS Axis paramete
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
Page 164 and 165:
Page 166 and 167:
Page 168 and 169:
Page 170 and 171:
Page 172 and 173:
Page 174 and 175:
Page 176 and 177:
5. MACHINE PARAMETERS Drive paramet
Page 178 and 179:
Page 180 and 181:
Page 182 and 183:
Page 184 and 185:
Page 186 and 187:
5. MACHINE PARAMETERS PLC Parameter
Page 188 and 189:
Page 190 and 191:
Page 192 and 193:
5. MACHINE PARAMETERS Tables CNC 80
Page 194 and 195:
Page 196 and 197:
Page 198 and 199:
6. CONCEPTS CNC 8037 ·198· Axes a
Page 200 and 201:
6. CONCEPTS CNC 8037 SOFT: V01.4X
Page 202 and 203:
Page 204 and 205:
Page 206 and 207:
6. CONCEPTS Jog CNC 8037 SOFT: V01.
Page 208 and 209:
Page 210 and 211:
Page 212 and 213:
Page 214 and 215:
Page 216 and 217:
Page 218 and 219:
Page 220 and 221:
Page 222 and 223:
6. CONCEPTS CNC 8037 ·222· Axis a
Page 224 and 225:
Page 226 and 227:
Page 228 and 229:
Page 230 and 231:
Page 232 and 233:
Page 234 and 235:
Page 236 and 237:
6. CONCEPTS CNC 8037 ·236· Refere
Page 238 and 239:
Page 240 and 241:
Page 242 and 243:
Page 244 and 245:
6. CONCEPTS Spindle CNC 8037 SOFT:
Page 246 and 247:
Page 248 and 249:
Page 250 and 251:
Page 252 and 253:
Page 254 and 255:
Page 256 and 257:
Page 258 and 259:
6. CONCEPTS CNC 8037 ·258· Digita
Page 260 and 261:
Page 262 and 263:
Page 264 and 265:
Page 266 and 267:
Page 268 and 269:
Page 270 and 271:
Page 272 and 273:
Page 274 and 275:
Page 276 and 277:
Page 278 and 279:
Page 280 and 281:
Page 282 and 283:
Page 284 and 285:
7. PLC RESOURCES Outputs CNC 8037 S
Page 286 and 287:
7. PLC RESOURCES Marks CNC 8037 SOF
Page 288 and 289:
7. PLC RESOURCES Timers CNC 8037 SO
Page 290 and 291:
Page 292 and 293:
Page 294 and 295:
Page 296 and 297:
Page 298 and 299:
Page 300 and 301:
7. PLC RESOURCES Counters CNC 8037
Page 302 and 303:
7. PLC RESOURCES Counters CNC 8037
Page 304 and 305:
8. INTRODUCTION TO THE PLC PLC reso
Page 306 and 307:
8. INTRODUCTION TO THE PLC CNC 8037
Page 308 and 309:
8. INTRODUCTION TO THE PLC Loop tim
Page 310 and 311:
Page 312 and 313:
Page 314 and 315:
8. INTRODUCTION TO THE PLC Modular
Page 316 and 317:
9. PLC PROGRAMMING CNC 8037 SOFT: V
Page 318 and 319:
9. PLC PROGRAMMING CNC 8037 ·318·
Page 320 and 321:
Page 322 and 323:
Page 324 and 325:
Page 326 and 327:
Page 328 and 329:
Page 330 and 331:
Page 332 and 333:
Page 334 and 335:
10. CNC-PLC COMMUNICATION CNC 8037
Page 336 and 337:
Page 338 and 339:
Page 340 and 341:
Page 342 and 343:
Page 344 and 345:
Page 346 and 347:
11. LOGIC CNC INPUTS AND OUTPUTS Ge
Page 348 and 349:
Page 350 and 351:
Page 352 and 353:
Page 354 and 355:
Page 356 and 357:
11. LOGIC CNC INPUTS AND OUTPUTS Ax
Page 358 and 359:
11. LOGIC CNC INPUTS AND OUTPUTS Ax
Page 360 and 361:
11. LOGIC CNC INPUTS AND OUTPUTS Sp
Page 362 and 363:
Page 364 and 365:
11. LOGIC CNC INPUTS AND OUTPUTS Ke
Page 366 and 367:
11. LOGIC CNC INPUTS AND OUTPUTS CN
Page 368 and 369:
Page 370 and 371:
Page 372 and 373:
Page 374 and 375:
11. LOGIC CNC INPUTS AND OUTPUTS Lo
Page 376 and 377:
Page 378 and 379:
11. LOGIC CNC INPUTS AND OUTPUTS Lo
Page 380 and 381:
12. ACCESS TO INTERNAL CNC VARIABLE
Page 382 and 383:
Page 384 and 385:
Page 386 and 387:
Page 388 and 389:
Page 390 and 391:
Page 392 and 393:
Page 394 and 395:
Page 396 and 397:
Page 398 and 399:
Page 400 and 401:
Page 402 and 403:
Page 404 and 405:
Page 406 and 407:
Page 408 and 409:
Page 410 and 411:
Page 412 and 413:
Page 414 and 415:
13. AXES CONTROLLED FROM THE PLC PL
Page 416 and 417:
Page 418 and 419:
Page 420 and 421:
Page 422 and 423:
Page 424 and 425:
13. AXES CONTROLLED FROM THE PLC Ac
Page 426 and 427:
14. PLC PROGRAMMING EXAMPLE CNC 803
Page 428 and 429:
14. PLC PROGRAMMING EXAMPLE First c
Page 430 and 431:
14. PLC PROGRAMMING EXAMPLE Main mo
Page 432 and 433:
Page 434 and 435:
Page 436 and 437:
Page 439 and 440:
Installation manual CNC TECHNICAL C
Page 441 and 442:
Installation manual Degree of prote
Page 443 and 444:
Installation manual PROBE CONNECTIO
Page 445 and 446:
Installation manual SUMMARY OF INTE
Page 447 and 448:
Installation manual Coordinate rela
Page 449 and 450:
Installation manual Other variables
Page 451 and 452:
Installation manual PLC resources S
Page 453 and 454:
Installation manual Sequence breaki
Page 455 and 456:
Installation manual General logic i
Page 457 and 458:
Installation manual Key inhibiting
Page 459 and 460:
Installation manual Auxiliary M, S,
Page 461 and 462:
Installation manual 2-DIGIT BCD COD
Page 463 and 464:
Installation manual KEY CODES Alpha
Page 465 and 466:
Installation manual LOGIC OUTPUTS O
Page 467 and 468:
Installation manual KEY INHIBITING
Page 469 and 470:
Installation manual CNC 8037 J. SOF
Page 471 and 472:
Page 473 and 474:
Page 475 and 476:
Installation manual M function Asso
Page 477 and 478:
Installation manual P P P P P P P P
Page 479 and 480:
Installation manual P P P P P P P P
Page 481 and 482:
Installation manual Cleaning MAINTE
Page 483 and 484:
Installation manual N. CNC 8037 SOF
show all

CNC 8037 - Installation manual - Fagor Automation

Create successful ePaper yourself

Delete template?

Save as template?