maxicoll 2013 catalog

Construction Chemicals
Pool Seramic
Adhesive Mortar
GRAY
POOL USED FOR
BONDING CERAMIC
Construction Chemicals
Pool Seramic
Adhesive Mortar
WHITE
POOL USED FOR
BONDING CERAMIC
POOL TILE ADHESIVE
Product Description
Cement-based, high-performance, highly flexible, thixothropic, with long working hours, as well as
providing water insulation adhesive.
Application Areas
• bonding Interior and exterior ceramic, granite, cotto, clinker, porcelain ceramic coating materials, such as
concrete, plaster, screed surfaces
• Old ceramic, granite, marble, ceramic or granite slabs ,
• Swimming pool, Turkish bath, spa, sauna, wet areas, such as glass mosaic water tank applications,
• Cold storage, freezing facilities, places where sudden temperature changes, such as floor heating
systems,
• Places with heavy pedestrian traffic load like and malls, hospitals, schools
Technical Specifications
• With high polymer content waterproofing features. Volumes of wet bonding applications, waterproofing
membrane.
• High adhesive strength. Caused by sudden temperature changes
• Flexibile to durable surface tensions.
• Vertical slip surface applications.
• Long open time.
• Easy to trowelEasy to trowel.
• Appearance: Grey or White powder
• Shelf Life: 12 months in original sealed packaging
Application Specifications
• Application temperature: (+5 ° C) - (+35 ° C)
• Mixing ratio: 5 - 5,5 L of water / 25 kg powder
• Pot Life: 6 hours
• Slip (EN 1308): 1 N/mm2
• Freeze-Thaw: cycles then> 1 N/mm2
• Flexibility (EN 12002):> 5 mm - S2 Very flexible
• Temperature Range: (-40 ° C) - (+80 ° C)
Application Instructions
• 25 kg TechnoPool should be added to 5 to 5.5 litre of water slowly and should be mixed to derive a
homogeneous mixture. This process should be done with a low speed mixer. Any additions should not be
included not mentioned in the procedures.
• Prepare mortar, wait for 5-10 minutes to mature . Before reapplication, stir for 1-2 minutes restart the
application again• Insulation material and the two types of bonding and waterproofing can be applied
where required.
• The first method is combined with bonding application. The important point in this application
iscompletely covering between the ceramic and the floor with adhesive Maxicoll pool, • The second
method, on the surface at first trowelForm a layer thickness of 1-2 mm. matchoval corner joints during the
application on the ground! iAfter Maxicoll paste operations pools should be operative after waiting for 24
hours.
• uses an adhesive mortar to obtain a better adhesion, spreading on the surface with the flat side of trowel
selected.according to the size of the tile with a notched trowel toothed part.
• the application of coating materials combined with large-sized (two-sided sliding) bonding method.
• glued onto the combed mortar Open time is 30 minutes, preferably by applying a force with a rubber
hammer. High temperatures, low humidity, wind, etc may shorten this time according toenviromental
conditions. Mortar expired paste operation on the mortar surface scraped.
• The mortar should be used within 4 hours.
• Expired or shell mortar should be discarded.
• avoidBuilding Maxicoll Pool Tiles with Mortar direct contact with water for at least 24 hours.
• After application tools and hands should be washed with plenty of water. Surfaces should be cleaned
with a damp cloth.
•Joint filling process, the wall 8 hours, after 24 hours on the ground.
Warnings
• Do not inhale cement dust. Avoid contact with bare skin and directly to eyes. in contact with skin and
eyes washwith plenty of water,
Do not inhale cement dust
Storage: Up to 10 layer stacks, stored in a dry environment.
Packing: 25 kg bags.
Certificates of Quality: TS EN 12004 C2TE S2.
C: Cement
2: High-performance
T: Vertical Slip
E: Extended working time
S2: Very Flexible