You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
CONTRIBUTION TO<br />
MULTI-PURPOSE MORTAR<br />
CONTRIBUTION TO MULTI-PURPOSE MORTAR<br />
Product Description<br />
Cement-based mortar, plaster, screed to increase the performance of materials such as synthetic<br />
rubber based liquid mortar additive.<br />
Application Areas<br />
Cement-based mortars flexibility, adherence and improves water tightness, repair slurries.<br />
Features<br />
• Bond strength is increased.<br />
• Abrasion resistant..<br />
• Permeability decreases. Flexibility is increased.<br />
• Resistance to freeze-thaw cycles<br />
• dilute acidic and basic solutions, salt water, and chemical resistant to oils.<br />
Technical Specifications<br />
Appearance: white liquid<br />
Shelf life: 12 months in original sealed packaging<br />
Density: 1.03 ± 0.03 g/cm3 pH value of 8 •<br />
Application Temperature: (+5 ° C) - (+35 ° C)<br />
Mixing ratio: 1/1-1/4 (according to the place and purpose of use)<br />
Consumption varies according to the place and purpose of use<br />
Application Instructions<br />
İmproved and the surface must be solid. The surface must be free of debris that may prevent adhesion.<br />
More air than needed to prevent the introduction of Maxicoli Mortar Additive. for different uses Mortar<br />
Additive Maxicoll recommended should be mixed with water according to the ratio in a suitable<br />
container. The concrete mixer should be placed, on the cement and fillers added. Lump in advance to<br />
avoid each other, mixing of cement and fillers are recommended elsewhere. Mortar should be mixed<br />
until a homogeneous mixture is obtained.<br />
Plaster mortars to use: Cement mixed with sand with a particle size sufficient amounts of the<br />
appropriate mixture (cement / sand ratio: 1/4 -1 / 5); Maxicoll Mortar Additive / Water: 1/4 by<br />
participating in enough water to the mortar mixture is obtained.<br />
Repair mortars to use: The prepared powder mortar (cement / sand ratio: 1/3 -1 / 4); Maxicoll Mortar<br />
Additive / Water: 1/2 the rate of repair mortar is obtained by participating in enough water to the<br />
mixture.<br />
Screeds use: First of all, for the preparation of the mortar to be used as adhesion enhancing layer,<br />
dust, mortar (cement / sand ratio: 1/3), Maxicoll Mortar Additive / Water: 1/2 percent should be added<br />
to the liquid mixture until the consistency. the thickness of 2 mm to be prepared mixture should be<br />
applied to the floor by brush. screed should be applied. for the preparation of the mixture containing<br />
Sufficient sand and cement screed (cement / sand ratio: 1/3 -1 / 4), Maxicofl Mortar Additive / Water:<br />
1/3 ratioenough water should be added to the mixture. Expired or shell mortar should be discarded.<br />
After the implementation of tools and hands should be washed with plenty of water. High temperatures,<br />
low humidity, wind, etc Maxicoll climatic conditions of the mortar must be improved carefully prepared<br />
with Mortar Additive. Rapid evaporation can cause shrinkage and surface cracks due.<br />
Warnings<br />
For more information refer to the Safety Data Sheet.<br />
Clean and dry place, between +5 ° C and +35 ° C, so that there must be stored out of direct<br />
sunlight. Must be protected from frost.<br />
Packaging: 5 Push, Push, plastic drums 10 and 20,<br />
Public Works Item No: 04.61314