Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Construction Chemicals<br />
Super Elastic Water<br />
Insulation Mortar<br />
Foundations, Retaining Walls, Terraces, Balconies, Pools<br />
Tanks and Basements For Curtain<br />
Two Component<br />
Super Elastic Water<br />
Insulation Mortar<br />
SUPER ELASTIC WATER INSULATION MATERIAL<br />
Cement - Concrete and Mortar Surfaces Acrilic applicable Elastic Water-Based Insulating Material<br />
Product Description<br />
SUPER ELASTIC, cement-based, two-component, polymer-modified structure that protects against<br />
cracking, high adherence, shrinkage and shrinkage-resistant insulation material<br />
Application Areas<br />
Most likely to stretch the effort to discourage any kind of load in reinforced concrete structures, water<br />
tanks, basic bundling, basement walls, terraces and balconies, wc, bathroom, balcony, To create a<br />
horizontal and vertical surfaces such as<br />
wet areas, swimming pools, a water impermeable layer under the screed and ceramic coatings.<br />
Features<br />
The elastic property is high, adherence is excellent. Shrinkage and cracking, positive water pressure,<br />
applied to the interior and exterior. Suitable for use with synthetic fibers or glass fibers. Prepared<br />
Consistency sholudbe applied with brush or trowel. Be applied by spraying, after use resistant to frost<br />
and corrosive salts,<br />
applied on moist surfaces. It is not corrosive, or ceramic coated with plaster .the drinking water<br />
storage is also available, free of toxic substances.<br />
Application<br />
Surface Preparation: Surfaces must be clean. chamfer the corners, air holes and loose particles that<br />
reduce adherence should be cleaned mechanically. Absorbent surfaces should be saturated.<br />
Mixing: Clear liquid component in a container on the dust component is added slowly,<br />
should mixedwith a low-speed mixer fora homogeneous mixture. Consistency of the material change<br />
according to the amount of fluid module . Component B is sufficient to use 90% applications are made<br />
with a trowel.<br />
Application Method: Surface defects repaired with Maxicol whether thin or thick repair mortar surface<br />
After satureted with water, damp, the first coat is applied.For Hardening of the material Wait<br />
approximately 3-5 hours after the second coat is applied. For each floor equal thickness of the material<br />
to be spread to all surfaces.IfThe weather is hot or too windy measures should be taken.<br />
Coverage: 2.5 to 3 kg/m2, depending on the application surface (two-floor)<br />
(A) Module powder, (B) Module liquid dark gray (after mixing) (A + B) mixture 1.65 kg / L of 20 ° C for 60<br />
min. 5 min 2 N/mm2 7 bar positive 2 days 7 days Min through out the coating application. After 3 days *<br />
CAUTION: Do not brush a coat if the application thickness is 2 mm, trowelshould not exceed 5 mm.<br />
Must not be left in direct sunlight or ceramic coated with a protective screed. The first 24 hours of outside<br />
applications, direct sun, wind, frost and rain protection is required.<br />
PACKAGE & STORAGE:<br />
A module of 20 kg.'Health moisture-resistant paper bags, B module 10 It.' ² canisters. Moisture-resistant<br />
bag, closed and stored in dry conditions for at least 12 months. Module B. Protect from frost.<br />
WARNING: cold ( +30 ° C) weather conditions should not be applied. The material must<br />
be avoidedto lose water rapidly. Use protective goggles and gloves when working. In case of contact<br />
with skin, wash skin with plenty of water. In case of contact with eyes, immediately consult a doctor.<br />
MAXICOLL technical support, or for more information, please contact Technical Support
Change language