Comfort 820 - Marantec

More documents

Recommendations

Info

3. General safety advice Please read carefully! Target group Mounting, installation and initial operation of this operator may only be carried out by specialist personnel! Qualified and trained specialist personnel are persons • who have knowledge of the general and special safety regulations, • who have knowledge of the relevant electro-technical regulations, • with training in the use and maintenance of suitable safety equipment, • with sufficient training and supervision by electricians, • who are able to recognize the special hazards involved when working with electricity. Warranty For a warranty with respect to functioning and safety the advices in these instructions have to be observed. Disregarding these warnings may lead to personal injuries or material damages. The manufacturer will not be liable for damages that might occur when neglecting this advice. Batteries, fuses and bulbs are excluded from warranty. To avoid installation mistakes and damages to the door and operator please follow exactly the mounting advice in these installation instructions. The system may only be used after thorough information on the respective mounting and installation instructions. Please keep these installation and operating instructions for further use. They contain important advice for operation, checks and maintenance. This item is produced according to the directives and standards mentioned in the Manufacturer's Declaration and in the Declaration of Conformity. The product has left the factory in perfect condition with regard to safety. Power-driven windows, doors and gates for industrial use must be checked before initial operation and if necessary, but at least once a year by a specialist (with documentation in writing)! Correct use The operator is meant to be used exclusively to open and close sliding entrance doors. Beside the advice in these instructions please observe the general precautions and safety regulations! Our sales and supply terms and conditions are effective. 4 Installation and operating instructions Comfort 820 GB (#70663)
3. General safety advice Please read carefully! Advice for installation of the operator • Make sure that the door is in mechanical good condition. • Make sure, that the door is balanced. • Make sure that the door opens and closes correctly. • Remove all components that are not required (e.g. cords, chains, angles etc.). • Switch off all devices which will not be needed after the operator is installed. • Before cabling works the operator has to be disconnected by all means from power supply and a waiting time of 10 sec. has to be kept in order to be sure that the operator is without power. • Observe the local safety regulations. • Always lay mains and control cables separately. The control voltage is 24 V DC. • Only mount the operator when the door is closed. • Install all impulse and control devices (e.g. RC code keypad) within sight to the door and in a safe distance to movable parts of the door. A minimum mounting height of 1,5 m has to be kept. • Following installation, ensure that door parts do not protrude onto public footpaths or streets. Advice for initial operation of the operator After initial operation, the door system operating personnel or their proxies must be familiarised with the use of the system • Make sure that no child will play with the door control unit. • Before movement of the door make sure that there are neither persons nor objects in the operating grange of the door. • Test all existing emergency command devices. • Never insert your hands into a running door or moving parts. Advice for maintenance of the operator To guarantee a function without faults, check and, if necessary, repair the following points. Always disconnect the operator from power supply before carrying out any works at the door system. • Check monthly whether the operator reverses as soon as the door meets an obstacle. For this put a 50 mm high / wide obstacle in the door travel path. • Check the settings of the "OPEN" and "CLOSE" power limit. • Check all movable parts of the door and operator system. • Check the door system for signs of wear or damages. • Check whether the door can be easily moved by hand. Advice for cleaning the operator For cleaning never use: direct jet of water, high pressure cleaner, acids or lye. • Clean the operator with a dry cloth if necessary. Installation and operating instructions Comfort 820 GB (#70663)5
Page 1 and 2: Comfort 820 Operator system for sli
Page 3: 2. Table of contents 1. Meaning of
Page 7 and 8: 4. Summary of the product Toothed r
Page 9 and 10: 5. Preparation for mounting 5.1 Gen
Page 11 and 12: 6. Mounting 6.1 Mounting the spur g
Page 13 and 14: 6. Mounting 6.2.1 / 4 q E H 15 ≥
Page 15 and 16: 6. Mounting 6.2.2 / 4 Attention! Li
Page 17 and 18: 6. Mounting 6.4 Adjustment of the t
Page 19 and 20: 6. Mounting 6.4.1 / 8 B • Pull th
Page 21 and 22: 6. Mounting 6.5.2 Operator with flo
Page 23 and 24: 6. Mounting 6.5.3 Operator with swi
Page 25 and 26: 6. Mounting 6.6 Mounting the refere
Page 27 and 28: 6. Mounting 6.6.3 Operator with swi
Page 29 and 30: 6. Mounting 6.8 Mounting the cover
Page 31 and 32: 6. Mounting 6.9 Connection of exter
Page 33 and 34: 7. Hand transmitter 7.2 Coding of t
Page 35 and 36: Installation and operating instruct
Page 37 and 38: 8. Control unit 8.2 Overview on the
Page 39 and 40: 9. Programming 9.1.2 Reference poin
Page 41 and 42: 9. Programming 9.2.3 Programming of
Page 47 and 48: 9. Programming 9.3.2 Programming se
Page 49 and 50: 9. Programming 9.3.4 Programming le
Page 51 and 52: 9. Programming 9.3.6 Programming le
Page 53 and 54: 10. Messages 10.2 Overview of the e
Page 55 and 56:
10. Messages Error Cause Remedy LED
Page 57 and 58:
11. Appendix Installation and opera
Page 59 and 60:
11. Appendix Legend spare parts 11.
Page 61 and 62:
11. Appendix 11.4 Manufacturer's De
Page 63 and 64:
11. Appendix Installation and opera
show all

Comfort 820 - Marantec

Create successful ePaper yourself

Delete template?

Save as template?