Comfort 820 - Marantec

More documents

Recommendations

Info

4. Summary of the product Support brackets The operator can be mounted with two different supports. Floor console 4.1 / 7 Swivel support 4.1 / 8 Advice! The swivel support cannot be combined with the toothed rack Special 471. 4.2 Mounting variations The operator can be mounted in two different variations. Mounting the operator with floor console Mounting the operator with swivel support 8 Installation and operating instructions Comfort 820 GB (#70663) 4.2 / 1 4.2 / 2 270 120 328 390
5. Preparation for mounting 5.1 General notes The pictures in these instructions are not true-to-scale. The sizes are always indicated in millimetres (mm)! Depending on the opening direction the operator can be mounted on the right or on the left side of the door. These instructions show the mounting on the right side. For correct mounting you will need the following tools: 5.1 / 1 13 ø 8 ø 10 ø 7 6 5 2 ø 3,5 ø 4,5 5.2 Checks Attention! Before you start to work, please always check the following points in order to guarantee correct mounting. Supply package • Check whether the supply package is complete. • Check whether all accessories required for your installation situation are at hand: - Spur gear - Toothed rack - Support bracket Foundation • Check the intended position of the operator: - The mounting of the operator must be carried out on the inside with the door closed. • - The operator must not be mounted in the clearance (q)! • Check whether there is a suitable foundation. • Check the laying of the supply line. Pay attention that the cable comes out on operator position (A). The minimum requirement for the earth cable is 3x1,5 mm 2 . Door • Check whether the sliding gate to be operated fulfils the following conditions: - The door has to be mounted horizontally, i.e. no slope in travel direction. • - In closed position the door should project the clear driveway by at least 250 mm on the installation side. - The door needs a mechanical end stop in both directions. • - The closing edges must be equipped with a flexible door sealing profile. Installation and operating instructions Comfort 820 GB (#70663)9
Page 1 and 2: Comfort 820 Operator system for sli
Page 3 and 4: 2. Table of contents 1. Meaning of
Page 5 and 6: 3. General safety advice Please rea
Page 7: 4. Summary of the product Toothed r
Page 11 and 12: 6. Mounting 6.1 Mounting the spur g
Page 13 and 14: 6. Mounting 6.2.1 / 4 q E H 15 ≥
Page 15 and 16: 6. Mounting 6.2.2 / 4 Attention! Li
Page 17 and 18: 6. Mounting 6.4 Adjustment of the t
Page 19 and 20: 6. Mounting 6.4.1 / 8 B • Pull th
Page 21 and 22: 6. Mounting 6.5.2 Operator with flo
Page 23 and 24: 6. Mounting 6.5.3 Operator with swi
Page 25 and 26: 6. Mounting 6.6 Mounting the refere
Page 27 and 28: 6. Mounting 6.6.3 Operator with swi
Page 29 and 30: 6. Mounting 6.8 Mounting the cover
Page 31 and 32: 6. Mounting 6.9 Connection of exter
Page 33 and 34: 7. Hand transmitter 7.2 Coding of t
Page 35 and 36: Installation and operating instruct
Page 37 and 38: 8. Control unit 8.2 Overview on the
Page 39 and 40: 9. Programming 9.1.2 Reference poin
Page 41 and 42: 9. Programming 9.2.3 Programming of
Page 47 and 48: 9. Programming 9.3.2 Programming se
Page 49 and 50: 9. Programming 9.3.4 Programming le
Page 51 and 52: 9. Programming 9.3.6 Programming le
Page 53 and 54: 10. Messages 10.2 Overview of the e
Page 55 and 56: 10. Messages Error Cause Remedy LED
Page 57 and 58: 11. Appendix Installation and opera
Page 59 and 60:
11. Appendix Legend spare parts 11.
Page 61 and 62:
11. Appendix 11.4 Manufacturer's De
Page 63 and 64:
11. Appendix Installation and opera
show all

Comfort 820 - Marantec

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?