HQ Studio Frame Manual for HQ Avante 08-09-11 ... - Handi Quilter

More documents

Recommendations

Info

HQ Studio Frame Box Contents Box No. 1 Parts Two 4-foot table sections with track supports (4) , M6 X 12mm Connector screw (8) and left and right pole brackets 2 10 poles, 10 couplers 3 All other parts (including plastic tracks) 4 Box No. 4 12' frame One 4-foot table section w/track supports (2), M6 X 12mm Connector screw (4), five 4-foot poles 10' frame (Boxes 1, 2 & 3 same as 12-foot) Parts One 2-foot table section with track supports (2), M6 X 12mm Connector screw (4), five 2-foot poles 4 HQ Studio Frame Assembly Visit http://www.HandiQuilter.com
Step 1 Frame Side Assembly Note: Assembly is easiest if all connections are finger-tightened first Fig. 2-1 as instructed, while assembling the frame. Tighten with the wrench when instructed. Why is this important? If you tighten as you go, you may have trouble getting all the parts to align properly. Note: Make sure both height- adjustable legs are at their shortest setting before proceeding. Remember that the batting bar bracket needs to be on the outside of the leg. (Fig. 1-1) Visit http://www.TheQuiltersAcademy.com QF09318-103 BUNGEE HOLDER QF09318-201 RATCHET STOP BUSHING QF09318-703 OUTSIDE POLE END QF09318-104 BUNGEE HOLDER COVER Step 1: Frame Side Assembly Parts needed 1-Right Side Leg 1-Left Side Leg 1-Right Frame Side Front 1-Left Frame Side Front 1-Right Frame Side Back 1-Left Frame Side Back 4-Leveling Feet 16-M8 x 16mm SBHCS M8 X 16 SBHCS X 4 QF09318-202 RATCHET STOP MOUNT QF09318-705 V-GROOVE BEARING Tools Required 5mm Allen Wrench (Provided) 1-1: Screw two (2) leveling feet about half way into the bottom of the left side leg, as shown in Fig. 1-1. 1-2: Attach the left frame side back onto the side leg using two M8 x 16mm SBHCS into the back of the back leg. Next install two more M8 x 16mm SBHCS into the side of the back leg. Finger-tighten the screws only for now. You will tighten the screws with an Allen wrench later in Step 4.8. 1-3: Attach the left frame side front onto the side leg using two M8 x 16mm SBHCS into the front of the front leg. Next install two more M8 x Left Frame Side Front Left Frame Side Back Back Leg Front Leg QF09318-103 BUNGEE HOLDER SPACER QF09318-204 CONNECTOR BOLT QF09318-713 HAND WHEEL COLLAR QF09318-105 RAIL BEARING SNAP QF09318-203 RATCHET STOP QF09318-714 STEEL SNAPPING BUTTON/LOCKING CLIP QF09318-106 RAIL BEARING SNAP COVER LEVELING FOOT QF09318-205 RATCHET STOP HOLDER QF09318-105 Fig. 10-2 QF09318-103 BUNGEE HOLDER QF09318-201 RATCHET STOP BUSHING QF09318-703 OUTSIDE POLE END QF09318-104 BUNGEE HOLDER COVER QF09318-202 RATCHET STOP MOUNT QF09318-705 V-GROOVE BEARING QF09318-103 BUNGEE HOLDER SPACER QF09318-204 CONNECTOR BOLT QF09318-713 HAND WHEEL COLLAR Leveling Feet Fig. 1-1 M8 X 16 SBHCS X 4 QF09318-105 RAIL BEARING SNAP Batting Bar Bracket Left Side Leg QF09318-203 RATCHET STOP QF09318-714 STEEL SNAPPING BUTTON/LOCKING CLIP QF09318-106 RAIL BEARING SNAP COVER Fig. 1-1 LEVELING FOOT 16mm SBHCS into the side of the front leg. Finger-tighten the screws only for now. You will tighten the screws with an Allen wrench later in Step 4.8. 1-4: Using remaining parts, repeat Steps 1-1 through 1-3 to complete the right side leg. QF09318-205 RATCHET STOP HOLDER HQ Studio Frame Assembly 5 QF09318-105 Fig. 10-2
Page 1 and 2: HQ Studio Frame for HQ 18 Avanté A
Page 3: 318-202 TOP MOUNT -705 EARING CONNE
Page 7 and 8: FIG. 4-1 Note: If instructions were
Page 9 and 10: Note: Make sure all height-adjustab
Page 11 and 12: 09318-02 Fig. 5-1 Place the track s
Page 13 and 14: this time. They need to be loose to
Page 15 and 16: shown in Fig. 6-1. If the ratchet s
Page 17 and 18: IMPORTANT: Be careful when assembli
Page 19 and 20: Fig. 9-2 Fig. 9-5 9-5: Slide one po
Page 21 and 22: F09318-106 Backing Pole ARING SNAP
Page 23 and 24: Visit http://www.TheQuiltersAcademy

HQ Studio Frame Manual for HQ Avante 08-09-11 ... - Handi Quilter

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?