SPM 05 ENvFIN.indd - Salomon Certification

More documents

Recommendations

Info

Reference 9 Jig Selection & Use 12 Retail Mounting 35 Rental & Demo Mounting 10 DRILLING, TAPPING & GLUE A Correct Incorrect Follow the recommendations of the ski manufacturer for drilling and tapping. In their absence, Salomon suggests that you use the Salomon Drill Bit Selection Guide. When in doubt about the ski’s core composition, select a 3.6 mm diameter bit and drill one hole. If the bit comes in contact with any metal, redrill with a 4.1 mm bit. Salomon Drill Bit Selection Guide S Drilling Skis Diameter Length Reference Aspect Junior Adult Diameter Special Cases When Drilling Junior Skis Adjustment 4.1 mm 8 mm 000813 3.6 mm 8 mm 000814 4.1 mm 9.5 mm 000893 3.6 mm 9.5 mm 000892 Length • Use a 9.5 mm length drill bit when mounting S910 Team, S608, and C608 and their earlier model predecessors. They use the same screws as adult models and should be drilled and tapped accordingly. • As a general rule, the S910 Team is mounted on skis 170 cm or longer and the S608 or C608 on skis 140–170 cm. The S608 or C608 can also be used with skis 120–140 cm. The S305 Grom and C305 Grom are generally used with skis Drill through the jig’s proper bushings applying moderate downward pressure on the drill. Verify that the countersink bevel on the drill bit has properly deburred the hole. Fig A After drilling, turn the ski over and hit the base several times with the palm of your hand to remove any debris from the drilled holes. 80-140 cm*. The shorter the ski, the more likely washers will be necessary to avoid dimpling the ski base. • The new Salomon C607 junior accommodates adult norm boot soles and offers a 2 to 7 DIN scale. This new intermediate binding for 5 to 10-year-olds features shorter 6 mm screws for use on junior skis as short as 120 cm. • Whenever junior bindings are mounted on adult skis, an increased possibility exists of binding pull-out When mounting thin skis or junior skis with adult bindings you may need to use shorter screws or add washers to the existing screws between the binding and the ski to prevent damaging the ski base. Before drilling any junior ski, check the screw depth by positioning the binding over the mounting area so that the binding screws on one side of the heel track appear alongside the ski sidewall. Fig S Plastic plugs Color Reference Blue 000821 Black 000818 White 000819 Grey 000822 Red 000820 Orange 000823 Green 000870 due to poor screw retention. The penetration depth of junior screws into the ski core is only 7 mm. If necessary, use adult drill bits and screws to penetrate any mounting platform. • The hole must be deep enough to accommodate the screw length you are using or ski damage may result. * EXCEPTION: S305’s and C305’s cannot be mounted on the Crossmax 10 Team or XScream 10 Team models manufactured from 2001 to 2003 inclusively. Both bindings may be mounted on the 2004-2005 models of the Crossmax 10T and Crossmax T.
A Tapping Adjustment Glue Adjustment Glue must be used when inserting binding screws to: • Lubricate the screw during insertion. • Create a watertight seal. • Ensure that the screws will hold while the ski is in use by acting as a dampener. Mounting Adjustment A Posidrive No. 3 screwdriver, not a Phillips, is used to mount Salomon bindings. Consult the Salomon Spare Parts Catalog for reference Tap all binding mounting holes unless otherwise recommended by the ski manufacturer. Failing to tap when necessary can result in topskin delamination, sidewall delamination, broken screws or damage to the ski core. The tap should be mounted into a brace. Position the Place a drop of glue on the surface of each hole. As the screw passes through the glue it coats itself. on the Salomon screws. They are available through your customer service representative. brace so the tap goes straight into the drilled hole. Fig A Apply only enough pressure to the brace to start the tap, as the tap is a self-cutting tool. A ski mounting plate is usually no more than 8 mm below the topskin. Tapping any deeper than 8 mm can strip the hole or break the RETAIL SYSTEMS tap. Each full turn of the brace cuts the tap approximately 2 mm into the ski. After tapping, turn the ski over and hit the base several times with the palm of your hand to remove shavings from the hole. > Additional Reference Retail Mounting Rental & Demo Mounting # 000816 Taps # 000817 Tap Brace # 000811 Glue # 000862 Posidrive Screwdriver (CAN) # B18486 Posidrive Bit 11 12 35
Page 3 and 4: CONTENTS 2 Introduction 4 Certifica
Page 5 and 6: INTRODUCTION Salomon Systems & Bind
Page 7 and 8: Certification & Indemnification SCH
Page 9 and 10: RETAIL SYSTEMS Proper procedures fo
Page 11: A SD F G H J K Legend 1 Handle with
Page 15 and 16: 13 12 A 14 S914 AXE+ 11 10 Mounting
Page 17 and 18: 16 17 A G 15 14 13 Mounting Powerax
Page 19 and 20: Assembly Measure boot sole length i
Page 21 and 22: Salomon Binding Interfaces RETAIL M
Page 23 and 24: Instructions Adjusting Pilot classi
Page 25 and 26: Fat Ski Brakes RETAIL MOUNTING FAT
Page 27 and 28: All current model Salomon bindings
Page 29 and 30: The Boot • Inconsistencies with I
Page 31 and 32: FINAL CHECKING TROUBLESHOOTING Boot
Page 33 and 34: FINAL CHECKING RETAIL RECORD KEEPIN
Page 35 and 36: RENTAL & DEMO SYSTEMS Proper proced
Page 37 and 38: RENTAL & DEMO MOUNTING 35
Page 39 and 40: 14 13 12 11 Mounting (continued) G
Page 41 and 42: A Toe Length Adjustment Rental Toe
Page 43 and 44: e 2 BOOTS: • Thermic Fit liner, S
Page 45 and 46: Pre-Season Binding Inspections Adju
Page 47 and 48: RENTAL & DEMO MOUNTING RENTAL SKIER
Page 49 and 50: Name: Street City Phone # Driver’
Page 51 and 52: Spheric Performance Models Procedur
Page 53 and 54: Quadrax Models - with Equalizer Pro
Page 55 and 56: Any incorrect use of a Salomon part
Page 57 and 58: Retail Guidelines Salomon bindings
Page 59 and 60: Replacement Procedures Step One. Ve
Page 61 and 62: POST ACCIDENT SKI EQUIPMENT Inspect
Page 63 and 64:
Ski/Binding Maintenance Record Boot
Page 65 and 66:
TECHNICAL REFERENCE 2004/2005 TECHN
Page 67 and 68:
DIN scale Height in mm Skier weight
show all

SPM 05 ENvFIN.indd - Salomon Certification

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?