SPM 05 ENvFIN.indd - Salomon Certification
SPM 05 ENvFIN.indd - Salomon Certification
SPM 05 ENvFIN.indd - Salomon Certification
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
13<br />
12<br />
A<br />
14<br />
S914 AXE+<br />
11<br />
10<br />
Mounting<br />
A long bit is needed<br />
(Posidrive Bit, CAN. only<br />
Ref. #B18486, for power<br />
drills and <strong>Salomon</strong> Manual<br />
Screwdriver Ref. #000862)<br />
to mount the 4-hole pattern<br />
toes as the front two screws<br />
must be inserted through<br />
the binding housing. Fig A<br />
Use a crisscross screwing<br />
pattern and insert each<br />
screw until nearly seated.<br />
L<br />
K<br />
J<br />
S D F<br />
Fig S Do not tighten until<br />
all the screws are in place.<br />
The baseplate of the AFD<br />
should be flush with the<br />
topskin of the ski and each<br />
screw should be flush<br />
with the baseplate of the<br />
toe piece. This procedure<br />
applies for all toe pieces<br />
with a four-hole pattern.<br />
H<br />
Legend<br />
15<br />
F<br />
1 Heel Track<br />
2 Heel Housing<br />
3 Heel Lever<br />
4 Heel Cup<br />
5 Treadle<br />
6 Brake Pedal<br />
7 Pressure Distributors<br />
8 Spheric Pedal/AFD<br />
RETAIL MOUNTING<br />
4-HOLE TOE<br />
Performance/Spheric Oversize<br />
G<br />
* Use <strong>Salomon</strong> grease (Ref. #0009<strong>05</strong>) on track.<br />
Heel Piece.<br />
Place the heel over the<br />
prepared holes and insert<br />
the screws using a crisscross<br />
screwing pattern.<br />
(Do not compress the ski<br />
brake before it is mounted<br />
on the ski.) Fig D<br />
Do not over tighten.<br />
D<br />
S<br />
A<br />
9 Toe Cup<br />
10 Toe Height Adjustment Screw<br />
11 Visual Indicator<br />
12 Housing<br />
13 Adjustment Screw<br />
14 Baseplate<br />
15 Brake Arm<br />
Lubrication Point*<br />
Ski Brake Installation<br />
Do not compress the<br />
ski brake before installing<br />
it. Place the two metal tabs<br />
on the front of the brake<br />
into the slots in the heel<br />
base plate Fig F. Rotate<br />
the rear of the brake<br />
downwards to start the<br />
screw in the track. Tighten<br />
screws with a hand screwdriver<br />
(4 Nm maximum).<br />
Note: The brake can be<br />
removed to facilitate ski<br />
maintenance.<br />
To remove it: turn the<br />
center screw counterclockwise<br />
and remove<br />
the brake.<br />
> Reference<br />
# 001156<br />
Jig Selection & Use<br />
Drilling, Tapping<br />
& Glue<br />
Binding-to-Boot<br />
Adjustments<br />
Maintenance<br />
& Repair<br />
SC System<br />
Demo / Cosmic<br />
13<br />
9<br />
10<br />
16<br />
48<br />
36